MC36350 MULTICOMP, MC36350 Datasheet - Page 2

• Manufacturer Part Number: MC36350
• Description: ESD BENCH MAT & GROUNDING CORD
• Manufacturer: MULTICOMP

Specifications of MC36350

• Mat Type: Bench
• Mat Color: Green
• Mat Material: Rubber
• Ground Terminals: Snap
• Length: 4ft
• External Width: 2ft
• Thickness: 3mm
• Surface Resistivity Mm: 1Mohm/sq
• Mat Features: Static Dissipative

Straight Earth Lead
ESD Bench Matting - Smooth Finish - Green
GUIDANCE ON USE:
Matting materials have a tendency to shrink slightly when first unrolled. In applications where length is critical, allow the
material to relax for at least 4 hours before cutting to size. Matting should always be trimmed with a sharp knife or razor blade.
RoHS COMPLIANCE:
None of the following materials are intentionally added in manufacturing this product: lead, mercury, cadmium, hexavalent
chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE) as outlined in the Directive 2002/95/
EC Article 4.1.
TEST RESULTS:
R
mat. A proper R
ESD STM-4.1 for R
R
resistance properties. The ESD STM-4.1 guideline for R
Surface Resistance / R
Bottom Resistance / R
Volume Resistance
Thickness
Temperature Resistance
Temperature
Relative Humidity
TG
TT
Disclaimer: This data sheet and its contents (the “Information”) belong to the Premier Farnell Group (the “Group”) or are licensed to it. No license is granted for the use of it other then for information purposes
in connection with the products to which it relates. No license of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied.
The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet
should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting
from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to
limit or restrict the Group’s liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. © Premier Farnell plc 2008.
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
Features:
One end supplied with a single ring terminal the other end features a 10mm
snap and 2 x 4mm banana sockets.
Material :
•
•
•
•
•
•
is the resistance from one point on the mat’s surface to the mat’s ground point, and is the fundamental electrical test for a
is the resistance from one point on the mat’s surface to another point. A proper R
Special conductive wire
Each straight cord contains 10 special conductive wires
Outer covered with Non-Conductive PU
Length: 10ft
Diameter of cord: 2.4 mm
Resistivity : 1M Ohm +/- 10%
TG
insures that a mat can conduct charge from a point on the surface to the mat ground point. The guideline in
TG
is 1x10
TG
TT
6
to 1x10
9
ohms. ANSI/ESD S-20.20 has an upper limit of <1 x10
Test Method:
SJ/T10694-2004
SJ/T10694-2004
GB/T14437-97
YY-1001
YY-1001
N/A
N/A
SPC
SPC
TT
is >1x10
082-0210 ESD Bench Matting & Grounding Strap - Smooth Finish MC36350 | November 10, 2010 9:51 AM
6
ohms.
Unit:
Ω
Ω
Ω
mm
o
o
%
C
C
TT
insures the consistency of the mat’s
9
ohms.
SPC
SPC
Value:
1x10
1x10
1x10
Permissable Tolerance +0.1
180 (Instantaneous Temp)
20-26
40-65
6
6
5
< R < 1x10
< R < 1x10
< R < 1x10
9
9
8