TGV101 TIMEGUARD, TGV101 Datasheet

TGV101

Manufacturer Part Number

TGV101

Description

SOCKET, SWITCHED, SINGLE, IP66

Manufacturer

TIMEGUARD

Datasheet

1.TGV101.pdf (2 pages)

Specifications of TGV101

Approval Bodies

BS1363

Colour

Dark Grey

Current Rating

13A

External Depth

75mm

External Length / Height

132mm

External Width

117mm

Ip/nema Rating

IP66

No. Of Gangs

Operating Temperature

RoHS Compliant

Svhc

No SVHC (15-Dec-2010)

Rohs Compliant

Yes

Current page: 1 of 2
Download datasheet (530Kb)

IP66 Products covered by

these instructions

TGVL01

TGVL02

TGVL03

TGVL05

TGV101

TGV201

TGV104

TGV204

TGV205

TGV203

TGV103

Installation and Operating

Weathersafe Vision

One gang two way switch 10AX

Two gang two way switch 10AX

One gang bell push

One gang double pole switch 20A

One gang socket switched 13A

Two gang socket switched 13A

One gang RCD spur

Two gang RCD protected socket

13A (passive/latching)

Two gang RCD protected socket

13A (active/non-latching)

Combined timer and socket

One gang switched fused spur 13A

Instructions

General

Please note that all instructions are to be left with the

customer after installation.

The Weathersafe Vision range is manufactured from

tough, durable thermoplastic, and is intended for use in

an outdoor environment, or one in which the protection

provided by the Weathersafe Vision range is required.

All the products are rated IP66, for protection against

water and dust. All Weathersafe Vision products need to

be ﬁ tted with waterproof cable and conduit entries to

maintain their IP rating once installed.

The weather plus range complies with the following

standards.

• IP66 rating: BS EN 60529

• Socket outlets: BS 1363

• RCD units: BS 7288

• Fused connection units: BS 1363

• Switches: BS EN 60669

• All products in the range comply with the low

Voltage: 230V AC 50Hz

Operating temperature range: -5° to 55°C

Installation instructions

• These products should be installed by a competent

• Disconnect the mains electricity supply

• The Weathersafe Vision range is designed to be

• The rear box shall be mounted on the wall using no.8

• If the mounting surface is uneven use a sheet of

Fig. 1

Rear Box (double)

4 x ﬁ xing holes for

no. 8 woodscrews

Drain feature,

use only lower if

required

Front cover

ﬁ xing holes

voltage directive LV 72/23/EEC and where

relevant the EMC directive 89/336/EEC

person (e.g. qualiﬁ ed electrician) in accordance with

these instructions and in compliance with the

appropriate clauses of the current edition if the IEE

wiring and building regulations. Sockets should be

connected via a suitable RCD device.

before installing.

mounted on a vertical ﬂ at surface, with socket outlets

not more than 1 metre above the ground.

wood screws and wall plugs if necessary (see ﬁ g. 1).

marine ply as a base plate then ﬁ t the rear box to it.

If conduit is to be used then please follow the

instructions below:

• The drain feature must be drilled out using

• If bottom entry conduit is used, there must be

• The relevant cable entry knockout should

• If two cable entry positions are used with

• Ensure that the gasket is correctly ﬁ tted,

Operating Instructions

Fig. 2

Single and double boxes – side view of bottom.

• The lid may be opened by pressing in the tab(s)

• Plugs may be inserted into the sockets and the

• The lid should then be closed to maintain the

a 5mm drill if top or side entry conduit is used.

Opening this drain hole will reduce the IP rating

of the product. Remember – open out the lower

drain feature only and only if required by

conduit entry being used.

adequate drainage from the lowest point of

the conduit.

be carefully removed by scoring the groove

around the knockout with a sharp knife and

then tapping it out with a small hammer.

A waterproof cable or conduit entry must

then be ﬁ tted in its place.

metal conduit, then earth continuity between

the conduits must be maintained.

and tighten the four screws (supplied) to ﬁ x

the front cover in place (see ﬁ g. 1). Do not

overtighten. Use of an electric screwdriver

is not recommended.

on the front to release the snaps and then lifting

the lid (see ﬁ g.2).

socket switches turned on.

IP rating taking care to ensure that the cables

are aligned with the centre of the cable seals

(see ﬁ g. 3). Finally engage the snaps (see ﬁ g. 2)

by pulling out the tab(s) while maintaining

pressure to close the lid.

Push here and lift up

Snaps

Fig. 3

Rear Box (double with 2 gang RCD sockets)

Cleaning

• Care should be taken when cleaning

• Inside the lid should only be wiped with a

• The outside can be cleaned with

• Solvent based cleaners should not be used.

• Advice should be sought before installing this

Weathersafe Vision Products with RCD’s

(TGV104, TGV204, TGV205)

Always test the RCD before use.

To test: Ensure supply is connected

RESET – press the grey (blue for TGV205) button

marked Reset (R), the status indicator should show red.

TEST – press the red button marked Test (T),

status indicator should show black. This indicates

that the RCD has been tripped and power has been

disconnected from the outlet.

RESET – press the grey (blue for TGV205) button

marked Reset (R) again, the status indicator

should show red.

If all the above operations work satisfactorily, the RCD

is safe for use.

If the procedure is not completed satisfactorily do not

use the RCD and seek professional advice.

In applications such as hand driers it may not be

practical to expect each user to test before use. In this

case we suggest an appropriate person applies the test

routine twice a day.

this product.

clean dry cloth.

mild detergent.

product in an environment where it is likely to

be subjected to chemicals, oils or solvents.

Cable aligned with

centre of seals

Status indicator

Related parts for TGV101

TGV101 Summary of contents

Page 1

... TGVL05 One gang double pole switch 20A not more than 1 metre above the ground. • The rear box shall be mounted on the wall using no.8 TGV101 One gang socket switched 13A wood screws and wall plugs if necessary (see ﬁ g. 1). TGV201 Two gang socket switched 13A • ...

Page 2

... For the second and third years or any difficulty in the first year telephone the helpline on 020 8450 0515 HELPLINE 020-8450-0515 or email helpline@timeguard.com For a product brochure please contact: Timeguard Ltd. 020-8452-1112 or email csc@timeguard.com A ...

Related keywords

TGV101 datasheet
TGV101 data sheet
TGV101 pdf datasheet
TGV101 component
TGV101 part
TGV101 distributor
TGV101 RoHS
TGV101 datasheet download