GP2000S40-0.080-02-4/4 Bergquist, GP2000S40-0.080-02-4/4 Datasheet

GP2000S40-0.080-02-4/4

Manufacturer Part Number

GP2000S40-0.080-02-4/4

Description

GAP PAD, 2000 S40, .08", 100X100MM

Manufacturer

Bergquist

Type

Thermal Padr

Datasheets

1.GP2000S40-0.040-02-44.pdf (1 pages)

2.GP2000S40-0.125-02-44.pdf (1 pages)

Specifications of GP2000S40-0.080-02-4/4

Operating Temperature Range

-60Â°C To +200Â°C

Length

100mm

Overall Width

100mm

Svhc

No SVHC (18-Jun-2010)

Breakdown Voltage Vbr

2.5kV

External Depth

2.0mm

External Width

100mm

Thermal Conductivity

2W/m.K

Current page: 1 of 1
Download datasheet (70Kb)

Features and Benefits

• Thermal conductivity: 2.0 W/m-K

• Low “S-Class” thermal resistance at very

• Highly conformable, low hardness

• Designed for low-stress applications

• Fiberglass reinforced for puncture, shear

Gap Pad 2000S40 is recommended for low-

stress applications that require a mid to high

thermally conductive interface material.The

highly conformable nature of the material

allows the pad to fill in air voids and air gaps

between PC boards and heat sinks or metal

chassis with stepped topography, rough

surfaces and high stack-up tolerances.

Gap Pad 2000S40 is offered with inherent

natural tack on both sides of the material

allowing for stick-in-place characteristics during

application assembly.The material is supplied

with protective liners on both sides.The top

side has reduced tack for ease of handling.

Note: Resultant thickness is defined as the final gap

thickness of the application.

The Bergquist Company -

North American Headquarters

18930 West 78th Street

Chanhassen, MN 55317

Phone: 800-347-4572

Fax: 952-835-0430

low pressures

and tear resistance

125

100

0.20

Thickness vs. Thermal Resistance

0.50

Thermal Resistance (C-in

Gap Pad 2000S40

1.00

The Bergquist Company -

European Headquarters

Bramenberg 9a, 3755 BT Eemnes

Netherlands

Phone: 31-35-5380684

Fax: 31-35-5380295

1.50

Highly Conformable,Thermally Conductive, Reinforced “S-Class” Gap Filling Material

www.bergquistcompany.com

2.00

/W)

2.50

The Bergquist Company - Asia

Room 15, 8/F Wah Wai Industrial Centre

No. 38-40, Au Pui Wan Street

Fotan, Shatin, N.T. Hong Kong

Ph: 852.2690.9296

Fax: 852.2690.2344

Typical Applications Include:

• Power electronics DC/DC; 1/4, 1/2, full bricks, etc.

• Mass storage devices

• Graphics card/processor/ASIC

• Wireline/wireless communications hardware

• Automotive engine/transmission controls

Configurations Available:

• Sheet form and die-cut parts

Building a Part Number

Note: To build a part number, visit our website at www.bergquistcompany.com.

GP2000S40

PROPERTY

Color

Reinforcement Carrier

Thickness (inch) / (mm)

Inherent Surface Tack (1- or 2-sided)

Density (g/cc)

Heat Capacity (J/g-K)

Hardness, Bulk Rubber (Shore 00) (1)

Young’s Modulus (psi) / (kPa) (2)

Continuous Use Temp (°F) / (°C)

ELECTRICAL

Dielectric Breakdown Voltage (Vac)

Dielectric Constant (1000 Hz)

Volume Resistivity (Ohm-meter)

Flame Rating

THERMAL

Thermal Conductivity (W/m-K)

1) Thirty second delay value Shore 00 hardness scale.

2) Young's Modulus, calculated using 0.01 in/min. step rate of strain with a sample size of 0.79 inch

modulus, refer to Bergquist Application Note #116.

–

0.020

TYPICAL PROPERTIES OF GAP PAD 2000S40

–

All statements, technical information and recommendations herein are based on tests we believe to be reliable, and

THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED

WARRANTIES OF MARKETABILITY AND FITNESS FOR PURPOSE. Sellers’ and manufacturers’ only obligation shall be to

replace such quantity of the product proved to be defective. Before using, user shall determine the suitability of the product

for its intended use, and the user assumes all risks and liability whatsoever in connection therewith. NEITHER SELLER NOR

MANUFACTURER SHALL BE LIABLE EITHER IN TORT OR IN CONTRACT FOR ANY LOSS OR DAMAGE, DIRECT,

INCIDENTAL, OR CONSEQUENTIAL, INCLUDING LOSS OF PROFITS OR REVENUE ARISING OUT OF THE USE OR

THE INABILITY TO USE A PRODUCT. No statement, purchase order or recommendations by seller or purchaser not

contained herein shall have any force or effect unless in an agreement signed by the officers of the seller and manufacturer.

–

0816

–

Gap Pad

IMPERIAL VALUE

0.020 to 0.125

-76 to 392

Fiberglass

>5000

Gray

V-O

2.9

0.6

6.0

2.0

Standard Options

NA = Selected standard option. If not selecting a standard

option, insert company name, drawing number, and

revision level.

0816 = Standard sheet size 8" x 16", or

00 = custom configuration

02 = Natural tack, both sides

Standard thicknesses available: 0.020", 0.040", 0.060",

0.080", 0.100", 0.125"

GP2000S40 = Gap Pad 2000S40 Material

METRIC VALUE

0.508 to 3.175

-60 to 200

Fiberglass

>5000

Gap Pad

Gray

V-O

310

2.9

0.6

6.0

2.0

2000S40

. For more information on Gap Pad

: U.S. Patent 5,679,457 and others

TEST METHOD

ASTM D2240

ASTM D5470

ASTM E1269

ASTM D374

ASTM D792

ASTM D575

ASTM D149

ASTM D150

ASTM D257

PDS_GP_2000S40_12.08

U.L. 94

Visual

—

Related parts for GP2000S40-0.080-02-4/4

Related keywords

GP2000S40-0.080-02-4/4 datasheet
GP2000S40-0.080-02-4/4 data sheet
GP2000S40-0.080-02-4/4 pdf datasheet
GP2000S40-0.080-02-4/4 component
GP2000S40-0.080-02-4/4 part
GP2000S40-0.080-02-4/4 distributor
GP2000S40-0.080-02-4/4 RoHS
GP2000S40-0.080-02-4/4 datasheet download