50514 EMIT, 50514 Datasheet - Page 3

• Manufacturer Part Number: 50514
• Description: FULL TIME CONTINUOUS MONITOR, LED
• Manufacturer: EMIT

Specifications of 50514

• Meter Display Type: LED
• External Height: 11.4cm
• External Width: 6.4cm
• External Depth: 3cm
• Weight: 192g
• Lead Free Status / RoHS Status: na

TB-6550 Page 3 of 4
H. 4mm Parking Snap: When touched by the operator, this
snap will deactivate the alarm for six seconds. This allows
time for the operator to disconnect the coil cord from the
wrist band and park it on this snap. While parked, the coil
cord disables the alarm, allowing the operator to leave the
workstation. The OPERATOR GROUND LED will remain
off while the cord is parked. Upon returning and removing
the coil cord from the parking snap, the operator has six
seconds to hook up to the wrist band before the alarm
sounds.
I. Auxiliary Ground: Unmonitored wrist strap banana jack
ground.
Installation
Remove the Continuous Monitor from the carton and
inspect for shipping damage. Confirm that the worksurface
is 1 x 10E7 ohms or less and has a conductive layer
such as Dual Layer Rubber or Dissipative 3-Layer Vinyl
or Micastat® Dissipative Laminate with conductive buried
layers. Each unit should include the following:
I. The Full Time Continuous Monitor may be mounted to
II. Install the Push and Clinch snaps 12-72 inches apart
III. Snap both ground cords to the push and clinch snaps
IV. Route the black ground cord to the monitor’s green
V. Route the green ground cord to the monitor’s green
VI. Insert the power cord into the power inlet of the monitor,
Operation
When the Full Time Continuous Monitor is installed to an
ESD protective worksurface and grounded via a power
cord, the green MAT GROUND LED and red OPERATOR
GROUND LED should be illuminated. The monitor takes 6
seconds to activate its alarm circuitry when it is first plugged
in.
• Correct wiring of the outlet is confirmed when the monitor
• The worksurface resistance is measured between the two
1
2
2
1
1
1
1
is plugged in (50514 only).
snaps installed to the mat worksurface (See Figure 3).
a convenient location using the included the Velcro ®
set. It is normally mounted toward the front edge of
a workstation where the LEDs are easily visible. See
Figure 3 for installation set-up.
from each other on the work surface mat. Make sure
that they pierce and clinch the bottom side of the mat.
installed to the work surface mat.
terminal block labeled MAT.
terminal block labeled GND.
and connect the other end to a proper voltage source.
Full Time Continuous Monitor
Mat Monitor Cords (black and green)
Push and Clinch Snaps
Velcro ® Set
09070 Desco Wrist Strap Kit
Power Cord (50514 only)
Certificate of Calibration
EMIT - 3651 Walnut Avenue, Chino, CA 91710 • [phone] • Fax [phone] • Website: DescoEMIT.com
Figure 3. Installation of the Full TIme Continuous Monitor
TO USE THE CONTINUOUS MONITOR:
1. Plug a wrist strap cord, not attached to the wristband,
into the monitored banana jack labeled OPERATOR on the
front of the unit (See Figure 2). This automatically activates
the selected operator channel. The red operator LED
should illuminate.
2. Remove the charges from your body by making contact
with a properly grounded ESD worksurface. Snap the
cord to the wristband, and fit it snugly onto your wrist.
This should silence the audible alarm and cause the
OPERATOR GROUND LED to switch from red to green. If
this does not happen, examine the wrist cord for continuity
or damage and your wrist band to ensure that it is securely
fit. If you have dry skin, apply an approved dissipative hand
lotion such as Desco Reztore™ ESD Hand Lotion. When
leaving the area, the user can take the wrist cord along or
attach it to the monitor parking snap. The audible alarm will
shut off in approximately 6-8 seconds when operator wrist
cord is removed from unit and will instantly shut off when
the cord is attached to the parking snap.
PARKING SNAP
The audible alarm is designed to alert both the operator and
supervisor. The parking snap feature allows the operator
to disconnect when leaving the work area without sounding
the audible alarm. It also provides a means for wrist cord
storage (red OPERATOR GROUND LED will illuminate).
When the operator touches the parking snap, the audible
alarm will disable for 6 seconds. The user can then
disconnect the wrist cord from the wrist band and attach it
to the parking snap for storage. If the operator removes
the wrist cord plug from the OPERATOR banana jack, the
audible alarm will sound for 6-8 seconds.
© 2009 DESCO INDUSTRIES INC.
Employee Owned