Y1135A AGILENT TECHNOLOGIES, Y1135A Datasheet
Y1135A
Specifications of Y1135A
Y1135A Summary of contents
Page 1
Agilent 34980A Multifunction Switch/Measure Unit Data Sheet • 8-slot mainframe with 21 mix-and- match plug-in modules so you can create ...
Page 2
... High-performance unit provides low-cost alternative to PXI and VXI switch and measurement platforms If you use automated test equipment for design validation or manufacturing, you now have a cost-effective alternative to PXI and VXI test-system platforms. The 34980A multifunction switch/measure unit provides compa- rable functionality that is much easier to use than PXI and VXI and costs less ...
Page 3
Easier signal routing with four 2-wire internal analog buses. You can route your measurements directly to the internal DMM, or you can connect to external instruments through the analog bus connector on the rear of the mainframe. And since you ...
Page 4
Standard interfaces take the has- sle out of connecting to your PC Standard Ethernet, USB and GPIB interfaces are included in every mainframe. Use one of the built-in interfaces that is already available in your computer you prefer, ...
Page 5
Free BenchLink Data Logger Software to Simplify data logging The BenchLink Data Logger software for the 34980A provides a convenient way to collect and analyze your data. This is a Windows® based application that uses a familiar spreadsheet envi- ronment ...
Page 6
Power and flexibility to get your job done Store recall instrum m ent setups s Set I date other s s ystem feature digit DMM measurements 1 ⁄ 2 ...
Page 7
Mix and match 34980A modules to create your own custom configuration The 34980A mainframe holds up to eight plug-in modules. Mix and match them to create a custom system to meet your switching and system control needs. You can easily ...
Page 8
The 34980A multiplexer modules can be used to connect one of many different points to a single point. You can connect to an external instrument, or scan multiple analog signals to the internal DMM. Choose from ...
Page 9
Multiple multiplexers can connect to the built-in analog buses, allowing you to scan up to 560 2-wire channels or 640 1-wire channels in a single mainframe. The 34921A also offers 4 channels for directly measuring current you need ...
Page 10
Table 3. Multiplexer selection table—specifications and characteristics Channels/configurations Switch type Input characteristics (per channel) Max volts Max current (DC, AC RMS) Switch current Carry current [6] Power (W, VA) Volt-Hertz limit General specifications [3] Offset voltage [3] Initial closed channel ...
Page 11
The 34980A matrix modules are full cross-point matrices that allow you to connect any row to any column. This is a convenient way to connect multiple test instruments to multiple points on a device under test. ...
Page 12
Table 4. Matrix selection table—specifications and characteristics 34931A Channels/configurations dual 4x8 8x8 4x16 Switch type Armature latching Input characteristics (per channel) Max volts ± 300 V Max current (DC, AC RMS) Switch current 1 A Carry current 2 A [2, ...
Page 13
The 34980A general-purpose switches can be used to route signals or to control other system devices. These switches are ideal for device actua- tion and switching loads or power supplies. Choose from the following features: • ...
Page 14
RF and microwave switch modules The 34980A offers a variety of RF and microwave switch modules— RF multiplexers, SPDT switching from DC to 26.5 GHz switch/ attenuator driver module that allows you to control switches or attenuators ...
Page 15
Typical crosstalk 0 dB -10 dB -20 dB -30 dB -40 dB -50 dB -60 dB -70 dB -80 dB -90 dB -100 dB 10 MHz 40 MHz 100 MHz 400 MHz 1 GHz 2 GHz Frequency 34942A Typical ...
Page 16
Table 6. RF and microwave selection table—specifications and characteristics 34941A Channels quad 1x4 Switch type 50 Ω unterminated, latching relays RF characteristics [2] Frequency range GHz [2] Insertion loss (< 80% RH) 100 MHz 0.15 ...
Page 17
This module allows you to control switches attenuators, and other devices external to the 34980A. The 34945A/ 34945EXT provides the power and control signals for many of the most popular microwave switches and attenuators. One 34945A/34945EXT ...
Page 18
I/O with memory and counter This module can be used to simulate or detect digital patterns. It has eight 8-bit digital I/O channels with hand- shaking, pattern memory, two 10 MHz counters with ...
Page 19
D/A converter with waveform memory This module has four independent, isolated channels that output DC voltage up to ± current up to ± 20 mA. The gain and offset can be adjusted on-the-fly. ...
Page 20
DIO, 2-channel D/A and totalizer The multifunction module offers the flexibility you need for system control. The 34952A has four 8-bit digital I/O channels, a 100-kHz gated totalizer, and two ± analog outputs—all ...
Page 21
Use this module to create your own custom designs inside the 34980A mainframe. You can control your custom circuits with access to both the +12 V and +5 V supplies, 28 relay drive lines and two 8-bit ...
Page 22
DMM accuracy ± reading + % of range) Includes measurement error, switching error, and transducer conversion error [4] Function Range DC voltage 100.0000 mV (with 34921A/22A/ 1.000000 V [10] 31A/32A) 10.00000 V 100.0000 ...
Page 23
Additional Low Frequency Error for ACV, ACI (% of reading) Frequency AC Filter Slow AC Filter Medium 100 Hz 0 0.06 100 Hz - ...
Page 24
Multi-Channel close speeds over GPIB (msec) Isolate or fixed mode Close 2 channels 0.97 Close 5 channels 0.43 Close 10 channels 0.22 Close 60 channels 0.13 Scanning measurement rates to bus or memory Direct measurements – direct to I/O ...
Page 25
Measurement characteristics with optional internal DMM DC voltage Measurement method Continuously integrating multi-slope III A-D converter A-D linearity 0.0002% of reading + 0.0001% of range range Input resistance 100 mV ranges Selectable 10 ...
Page 26
Measurement characteristics with optional internal DMM continued [4] DC Operating Characteristics [5] Function Digits Readings/s [7] DCV , DCI, and 0.6 (0.5) 2 Resistance (≤10 kΩ ( (50) ...
Page 27
General specifications Power supply Universal 100 V to 240 V ± 10% Power line frequency 50 – ± 10% automatically sensed Power consumption 150 VA Operating environment Full accuracy for 0 ° °C Full accuracy to ...
Page 28
... Y1140A – 78-pin female solder cup connector kit 2 – 50-pin Dsub, Male 3493xT Terminal block with screw connectors Y1135A – 1.5 m 50-pin M/F Dsub cable Y1136A – 50-pin M/F Dsub cable Y1139A – 50-pin female solder cup connector kit 2 - 78-pin Dusb, Male 34939T Terminal block with screw connectors Y1137A – ...
Page 29
... Y1142A – 78-pin male solder cup connector kit 1 – 50-pin Dsub, Female 3495xT Terminal block with screw connectors Y1135A – 1.5 m 50-pin M/F Dsub cable Y1136A – 50-pin M/F Dsub cable Y1141A – 50-pin male solder cup connector kit 26- & 40-pin internal ...
Page 30
... Cables used for direct cable connection to module. some modules require 2 cables Y1135A 1.5 m 50-pin Dsub, M/F twisted pair with outer shield cable – 300 V Y1136A 3 m 50-pin Dsub, M/F twisted pair with outer shield cable – 300 V Y1137A 1.5 m 78-pin Dsub, M/F twisted pair with outer shield cable – 300 V Y1138A 3 m 78-pin Dsub, M/F twisted pair with outer shield cable – ...
Page 31
... Spain 34 (91) 631 3300 Sweden 0200- Switzerland 0800 United Kingdom 44 (0) 118 9276201 Other European Countries: www.agilent.com/find/contactus Revised: July 2, 2009 Product specifications and descriptions in this document subject to change without notice. © Agilent Technologies, Inc. 2009 Printed in USA, August 27, 2009 5989-1437EN ...