E2677A AGILENT TECHNOLOGIES, E2677A Datasheet
E2677A
Specifications of E2677A
E2677A Summary of contents
Page 1
... To ensure that you have the tools for dependable oscilloscope measurements, Agilent Technologies offers a wide range of oscilloscope probes and accessories. Each is designed for a specific measurement need because the physical and electrical quality of the connection can make the difference between a good measurement and a bad one. ...
Page 2
Probe Compatibility Table For ordering information when replac- ing your probe or probe accessory: Refer directly to the page number listed in the table of contents for your probe model. Probe Type Probe Model General Purpose Passive 1160A, 10:1 500 ...
Page 3
General Purpose Probes Overview Passive voltage probes are used for general purpose probing and are made with passive compo- nents only such as wires, connec- tors, capacitors and resistors (when attenuation is required). There are no active components such as ...
Page 4
... Impedance Passive 10073C High 500 MHz Impedance Passive 4 Standard accessories included: • General-purpose retractable hook tip hooks onto wires and test points for hands-free probing • Ground bayonet provides short, flexible ground lead for high- frequency measurements • General-purpose alligator clip ...
Page 5
... Approximate propagation delay Maximum input voltage Environmental Characteristics Temperature (operating) Humidity (operating) Altitude (operating) Shock Ordering Information Probes and Accessories Part # Description 10070C 1:1, 1 MΩ, 1.5 m passive probe 10073C 10:1, 2.2 MΩ 1.5 m passive probe 10072A Fine-pitch probing kit with 2 dual-lead adapters 10075A 0 ...
Page 6
General Purpose Probes Agilent 116XA Family Passive Voltage • Economical, easy to use • Compact design, removable probe handle for tight probing areas • Agilent 1163A, 500 Ω resistive divider, 10:1 attenuation Built for Reliability These general purpose replace- ment ...
Page 7
General Purpose Probes Agilent 116XA Family Passive Voltage Specifications System Model Bandwidth Number Type of Probe (scope +probe) 1160A High Impedance, 500 MHz Passive 1161A High Impedance, 500 MHz Passive 1162A High Impedance, 25 MHz Passive 500 Ω Resistive 1163A ...
Page 8
... MΩ, 1.5 m, miniature passive probe 5063-2143 Probe tip to BNC (m) IC clips: See “Probing Accessories” Horizontal and vertical mini-probe sockets: See “Probing Accessories” Wedge Probe Adapters: See “Probing Accessories” Replacement Parts Part # Description 5063-2135 General purpose retractable hook tip ...
Page 9
... ICs, surface mount devices, and dense circuit boards. The probe fits directly onto stan- dard board headers and IC clips. A range of accessories are avail- able for you to optimize interfac- ing with surface mount devices. Wedge Probe Adapters make con- venient and reliable connections to TQFP/PQFP package leads. See “ ...
Page 10
... Ordering Information Probes and Accessories Part # Description 1171A 10:1, 10 MΩ, 1.4 m, low mass passive probe IC clips: See “Probing Accessories” Wedge Probe Adapters: See “Probing Accessories” Replacement Parts Part # Description 5063-2122 Browser 10 Probe Parts Supplied ...
Page 11
High-Frequency Voltage Probes Overview Active voltage probes contain an active component, usually a field- effect transistor (FET), and there- fore need to be powered. A FET input has the advantage of pro- viding a very low input capaci- tance, typically ...
Page 12
... Both probe tips of the differential probe can “flex” to support various probing angles and target system characteristics (z-axis compliance). Innovative damped-wire accessories com- pensate for the inductance and capacitance associated with the leads, and prevent distor- tion of the measured signal. ...
Page 13
High-Frequency Active Differential/Single-Ended Probe System Agilent 1130A/31A/32A/34A InfiniiMax High-Performance Active Probe System Specifications Operating Characteristics Probe bandwidth* 1134A: > 7 GHz 1132A: > 5 GHz 1131A: > 3.5 GHz 1130A: > 1.5 GHz Rise and fall time (10% to 90%) ...
Page 14
... InfiniiMax single-ended browser probe head and accessories. Includes 2 ground collar assemblies, 10 replaceable tips, a ground lead socket and ergonomic handle. Order E2663A for replacement accessories. E2677A InfiniiMax differential solder-in probe head and accessories. Includes 20 full bandwidth and 10 medium bandwidth damping resistors. Order E2670A for replacement accessories. ...
Page 15
... Agilent support options to choose from. Controlled impedance transmission lines in every probe head deliver full performance versus the performance limitations produced by traditional wire accessories. Probe interface software allows you to save the calibration information for different probe heads per channel and will automatically retrieve calibration data for a probe amplifier attached to the scope ...
Page 16
High-Frequency Active Differential/Single-Ended Probe System Agilent 1168A/69A InfiniiMax II High-Performance Active Probe System Specifications Operating Characteristics Bandwidth* Rise and fall time • Probe only • When phase compensated by 80000 Series oscilloscope System bandwidth (–3 dB) 1 Input capacitance Input ...
Page 17
... InfiniiMax single-ended browser probe head and accessories. Includes 2 ground collar assemblies, 10 replaceable tips, a ground lead socket and ergonomic browser handle. Order E2663A for replacement accessories. E2677A InfiniiMax differential solder-in probe head and accessories. Includes 20 full bandwidth and 10 medium bandwidth damping resistors. Order E2670A for replacement accessories. ...
Page 18
... IC legs with little chance of shorting. It’s easy to insert and it stays put. For more information on the Wedge, see “Probing Accessories.” Leads are available for connecting to a wide variety of test points. See “Ordering Information” for a complete list. ...
Page 19
... Denotes specified parameters. All others are characteristics. Ordering Information Probe and Accessories Part # Description 1155A Low mass, 2-channel active probe IC clips: See “Probing Accessories” Wedge Probe Adapters: See “Probing Accessories” Replacement Parts Part # Description 01145-61602 Probe tip and cable 16517-82104 SMT leads ...
Page 20
... Superior Accessories Your device under test (DUT) determines the type of probing accessories you need. Of course, there are electrical trade-offs depending on the type of connec- tion you use. Longer connections from your DUT produce lower performance probing systems. ...
Page 21
High-Frequency Active Single-Ended Voltage Probes Agilent 1156A/57A/58A High-Bandwidth, Active Single-Ended Voltage Specifications Operating Characteristics Bandwidth (–3 dB) 1156A: > 1.5 GHz; 1157A: > 2.5 GHz; 1158A: > 4 GHz System bandwidth (–3 dB) 1156A with MSO/DSO8104A, 54832B/D, 54833A/D scope: 1 ...
Page 22
... Two solderable-tip 5 cm ground leads Includes user’s guide and one-year warranty. These accessories are properly damped to give you a flat transmitted response and non-resonant input impedance. Use these supplied accessories to get the best performance from your probe. Two solderable-tip 5 cm resistive ...
Page 23
High-Frequency Passive Voltage Probe Agilent 54006A 6 GHz Resistor Divider Probe • Useful in probing high-frequency signals with low source impedance • Supplied with 10:1, 500 Ω and 20:1, 1 kΩ resistor dividers • Low capacitive loading to extremely high ...
Page 24
Differential Voltage Probes Overview Differential probes are active probes with two inputs, one posi- tive and one negative, as well as a separate ground lead. They are used to look at signals that are referenced to each other instead of ...
Page 25
Active Differential Voltage Probes Agilent 1153A Low-Bandwidth Active Differential Voltage • View of low-bandwidth differential signals in the presence of much larger common-mode signals • 200 MHz bandwidth • Input from ±300 mV (dc + peak ac) to ...
Page 26
Active Differential Voltage Probes Agilent 1153A Low-Bandwidth Active Differential Voltage Specifications Operating Characteristics Bandwidth (–3 dB 200 MHz [1] Rise time 1.75 ns calculated from t 2% (with 50 ± 0.1 Ω load) dc gain accuracy* dc attenuator ...
Page 27
... Figure 4.4. dc component in a signal blocked using low-frequency reject without degrading low-frequency CMRR. Ordering Information Probe and Accessories Part # Description 1153A 200 MHz differential probe 5959-9335 Long (5.5 inch) test lead IC clips: See “Probing Accessories” Probe Parts Supplied One 10:1 One 100:1 attenuator attenuator adapter adapter One differential ...
Page 28
Current Probes Overview Current probes sense the current flowing through a conductor and convert voltage that can be viewed and measured on an oscil- loscope. There are two types of current probes for oscilloscopes, ac current probes ...
Page 29
Current Probes Agilent 1146A ac/dc Current • Low-cost solution • ac/dc currents measured simultaneously • Accurate measurements of currents: 100 mA to 100 Arms 100 kHz • Load impedance > 1 MΩ/100 pF Within Budget, Without Compromise The ...
Page 30
Current Probes Agilent 1146A ac/dc Current Specifications Operating Characteristics Current range* 100 mV/A: 100 peak; 10 mV/ 100 A peak Output signal 1000 mV peak max ac current accuracy* Range (after calibration and for ...
Page 31
Current Probes Agilent 1147A High Bandwidth ac/dc Current • General purpose, high-frequency current probing • ac, dc currents measured simultaneously • MHz bandwidth • continuous peak dc and ac pulse current Accurate Current ...
Page 32
Current Probes Agilent 1147A High Bandwidth ac/dc Current Operating Characteristics Bandwidth (–3 dB MHz 1 Rise time 7 ns Accuracy* ±1% of reading ±1 mV Maximum continuous current 15 A (acrms + dc) Refer to derating curves ...
Page 33
High-Voltage Passive Probes Overview High-voltage probes are used for voltages higher than can be han- dled safely with general-purpose 10:1 passive probes. For example, the maximum voltage for the 116XA general-purpose passive probes included with most Infiniium models is 300 ...
Page 34
... Maximum input 4000 Vpk Compensation range Probe readout Yes Cable length 1.8 m Ordering Information Probe and Accessories Part # Description 10076A High-voltage probe includes one retractable hook tip, one ground bayonet, one IC probing tip, one alligator ground lead, and a compensation screwdriver. 34 Figure 6.3. Compact design and long cable of the Agilent 10076A for probing small, power electronics components ...
Page 35
... Dimensions 2 cm (maximum width of probe stem after handle cm; 7.5 cm (maximum probe width at probe handle Ordering Information Probe and Accessories Part # Description N2771A High-voltage probe includes one alligator ground lead, one sharp probe tip, and one hook probe tip. ...
Page 36
Mixed-Signal Oscilloscope Logic Probe Kit • Same cable used for high-performance Agilent logic analyzers • Flying leads offer flexibility and convenience • IC clips with twin hooks are designed for fine surface mounted components MSO probes offer great value and ...
Page 37
Agilent E5396A Half-Size Soft Touch Connectorless Logic Probe • 17 channels, single-ended clock and data • < 0.7 pF equivalent load capacitance • Capable of data rates > 2.5 Gb/s (maximum rate depends on analyzer used) • 500 mV p-p ...
Page 38
... Probing Accessories Wedge Adapters Agilent Wedge Probe Adapters • Secure connection to 0.5 mm and 0.65 mm TQFP and PQFP devices • Won’t fall off, short against adjacent legs, or degrade signal quality • Can be inserted while the board is active • and 16 signal versions ...
Page 39
... Probing Accessories 0 Clips, PC Board Mini-Probe Sockets 0 Clips • Extremely small size • Thin body for mounting multiple clips side-by side • Connection to PQFP and SOIC SMT packages from 0.5 to 0.8 mm (0.020 in. to 0.032 in.) lead pitch The 0 clips connect directly to the Infiniium MSO ...
Page 40
... Probe rotation range Infinite Note: The EZ-Probe Position’s vacuum base requires up to -15.75 inch Hg vacuum for proper operation. Cascade Microtech offers vacuum pumps as well as many other EZ-Probe accessories. Ordering Information Contact Cascade Microtech at www.cascademicrotech.com to order 40 Figure 9.4. A fully articulated arm allows ...
Page 41
Logic Analyzer/Oscilloscope Time Correlation • Cross-trigger and time-correlate oscilloscope and logic analyzer measurements • Simultaneously display oscilloscope and logic analyzer waveforms • No correlation fixture required, optional for most precise correlation Some of the toughest measure- ment test problems involve ...
Page 42
VoiceControl • Hands-free scope operation • Speaker and gender independent • Uses simple English commands If you’re making multi-channel measurements on target systems with densely packed ICs, your hands are tied up holding probes, making it difficult to turn knobs ...
Page 43
... The Agilent 1184A testmobile gives you a convenient means of organizing and transporting your Infiniium oscilloscope and acces- sories. The testmobile includes a drawer for accessories (probes, cables, power cords, etc.) and a keyboard tray with adjustable tilt and height. For more information, refer to the “Agilent Test and Measurement Catalog” ...
Page 44
... E2625A Communications Mask Test Kit E2699A My Infiniium Integration Software Related Literature Publication Title Agilent Technologies Digital and Mixed Signal Oscilloscopes Infiniium 8000 Series Oscilloscopes Infiniium 54850 Series Oscilloscopes and InfiniMax 1130 Series Probes Infiniium 80000 Series Oscilloscopes and InfiniMax II Series Probes ...
Page 45
... Agilent Technologies’ Test and Measurement Support, Services, and Assistance Agilent Technologies aims to maximize the value you receive, while minimizing your risk and problems. We strive to ensure that you get the test and measurement capabilities you paid for and obtain the support you need. Our extensive support resources and services can help you choose the right Agilent products for your applications and apply them successfully. Every instrument and system we sell has a global warranty. Two concepts underlie Agilent’ ...