LD6A-5WQB-RYSGW IDEC, LD6A-5WQB-RYSGW Datasheet - Page 12

• Manufacturer Part Number: LD6A-5WQB-RYSGW
• Description: SIGNAL LIGHT TOWER, RED/YEL/BLUE/GRN/WHT
• Manufacturer: IDEC

Specifications of LD6A-5WQB-RYSGW

• Base Type: Flush
• Supply Voltage: 24V
• Power Rating: 0.6W
• Current Rating: 25mA
• Ip/nema Rating: IP65
• Lamp Base Type: Flush
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Replacement and Addition of LED Modules
•
•
•
•
•
•
•
•
•
•
Wiring
•
•
•
•
•
•
•
•
•
•
•
1
Make sure to turn power off.
Insert a flat screwdriver into the cap recess as shown below, lift up the cap, and
remove with your hands. Use a flat screwdriver with maximum 1-mm thick and
7-mm wide tip.
Remove the center screw before reassembling the LED modules.
When assembling the LED modules, make sure to align the recess of the cap with
the recess of the LED module. Otherwise, damage may result.
Recommended tightening torque: 0.4 to 0.5 N·m.
Note the correct orientation when assembling the LED modules.
Tighten the screws to the recommended tightening torque. The LED module may be
damaged if the screw is loose during operation.
Do not touch the metal plug on the LED module. Otherwise, LED elements maybe
damaged due to static electricity.
Use a maximum of 5 tiers.
Select the correct screw length depending on the number of tiers.
Do not remove the gasket from the LED module. Otherwise, the waterproof seal
will be compromised.
For wiring, see the wiring diagrams on pages 9 and 10.
Incorrect wiring may damage the internal circuit.
Be sure to insulate unused wires.
Connect a 1A fuse to the power line as shown in the Wiring Examples on pages 9
and 10.
Use a UL listed external fuse holder.
Use a class 2 power supply only.
When using LED modules of the same color for two or more tiers, determine
contact capacity in referencet to the LED current, because only one wire is used to
light all tiers of the same color.
Do not apply voltage to flashing (brown) lines.
Do not connect flashing (brown) line to the power lines. The internal circuit may be
damaged.
Do not turn on steady and flashing circuits simultaneously.
Do not turn on alarms 1 and 2 simultaneously.
USA
IDEC Corporation
Tel: [phone]
opencontact@IDEC1com
Canada
IDEC Canada Ltd.
Tel: [phone]
sales@ca1IDEC1com
Australia
IDEC Australia Pty. Ltd.
Tel: [phone]
sales@au1IDEC1com
Insert flat screwdriver into recess
2
Japan
IDEC Corporation
Tel: [phone]
United Kingdom
IDEC Electronics Ltd.
Tel: [phone]
IDEC@uk1IDEC1com
products@IDEC1co1jp
3
Specifications and other descriptions in this catalog are subject to change without notice1
Top Cap
LED module
©2010 IDEC Corporation1 All Rights Reserved1
Catalog No1 LD9Y-B100-0 4/10 10K
Recess
Recess
Recess
Gasket
Recess
www.IDEC.com
Germany
IDEC Elektrotechnik GmbH
Tel: [phone]
service@IDEC1de
Hong Kong
IDEC (H.K.) Co., Ltd.
Tel: [phone]
info@hk1IDEC1com
Wire Color
For information on external contacts, see “External Contact Ratings” on page 6.
Alarm Volume Adjustment
•
•
•
High Temperature Limitations
The external temperature cannot exceed 50ºC when all tiers are lit at the same time
in the following combinations:
1.
2.
Alarm volume
adjustment lever
Wire Color
Red
Orange
Blue
Green
White
Purple
Light Blue
Brown
Gray
Yellow
Move the volume adjustment to the right or left to change the volume.
When the adjustment lever is all the way to the right the volume is at its maximum.
The adjustment lever may be damaged if forced.
Three tiers
Two or more tiers of blue and green (example: Red-Green-Blue,
Green-Green-Red)
Four or five tiers (example: Red-Yellow-Green-Pure White, Red-Yellow-Blue-
Green-Pure White)
Min.
Steady
LED Module – Red
LED Module – Yellow
LED Module – Blue
LED Module – Green
LED Module – Pure White
—
—
—
—
Power Line
China/Beijing
IDEC (Beijing) Corporation
Tel: [phone]
idec@cn1IDEC1com
China/Shanghai
IDEC (Shanghai) Corporation
Tel: [phone]
idec@cn1IDEC1com
www.IDEC.com/usa/LD6A
Max.
800-262-IDEC
Steady, Flashing, Alarm
LED Module – Red
LED Module – Yellow
LED Module – Blue
LED Module – Green
LED Module – Pure White
Alarm 1
Alarm 2
Flashing COM
Power Line
Power Line
China/Shenzhen
IDEC (Shenzhen) Corporation
Tel: [phone]
Singapore
IDEC Asia Pte. Ltd.
Tel: [phone]
info@sg1IDEC1com
Taiwan
IDEC Taiwan Corporation
Tel: [phone]
service@tw1IDEC1com