LJ-TX43-01 LPRS, LJ-TX43-01 Datasheet

LJ-TX43-01

Manufacturer Part Number

LJ-TX43-01

Description

TRANSMITTER, REMOTE SWITCHING, FOB

Manufacturer

LPRS

Datasheet

1.LJ-TX43-01.pdf (4 pages)

Specifications of LJ-TX43-01

Rohs Compliant

YES

Current page: 1 of 4
Download datasheet (61Kb)

Low Power Radio Solutions Ltd

SPECIFICATION

REMOTE SWITCHING UNIT RCU-01

Standard system comprises: -

1 Receiver unit

1 Transmitter (Radio key)

Pre-Coded

RECEIVER SWITCHING UNIT

SUPPLY 10 – 24 V AC/DC

RADIO FREQUENCY 433.92 MHz AM

OPERATING TEMP -20°C to + 70°C

RELAY 8A @ 240V AC

CONNECTION SCREW TERMINALS

DIMENSIONS H 75mm, W 50mm, D 27mm (Excluding 155mm aerial and gland)

TRANSMITTER

RF OUTPUT 433.92 MHz AM

SUPPLY 12V Battery

CODE 24 BIT

LICENCE WT MPT 1340 LICENCE EXEMPT

DIMEMSIONS H 57mm, W 36mm, D 15mm

As with all radio frequency based equipment, it is possible that external interference and environmental

conditions can significantly affect the performance, therefore it is essential that this product is not used

where failure of operation could be considered dangerous or result in damage or loss to property.

In the interest of continued development, the manufacturer reserves the right to alter the specification of

this product without prior notice.

For further information contact

Low Power Radio Solutions Ltd

Two Rivers Industrial Estate

Station Lane

Witney

Oxon

OX28 4BH

TEL: 0044 (0) 1993 776488

Email:

info@lprs.co.uk

Website:

www.lprs.co.uk

The RCU-01 is a radio remote controlled switching unit that will allow the remote operation of any

appropriate electrical appliance that is required. The unit is constructed to commercial standards, giving the

convenience of remote operation and in most cases the reduction in installation costs will exceed the cost

of switching unit.

The output of the unit is in the form of a relay change over contact rated at 8 amps 240V AC.

On the reception of a valid signal the output can be programmed to be momentary, toggled or timed using

the internal dipswitches.

The remote control is achieved by using an encoded UHF radio signal produced by a key fob transmitter

with a super-heterodyne receiver validating the transmitted code and activating the output accordingly.

The RCU-01 receiver requires a supply of 10 to 24V AC/DC and the output is via a pair of voltage free

changeover relay contacts.

INSTALLATION

First remove the lid and carefully retain the 4 lid screws.

The DIPswitches should be positioned in line with the table (overleaf), in order to es tablish the correct

output control (Latched, momentary or timed).

RCU01

11/08/2006

Related parts for LJ-TX43-01

LJ-TX43-01 Summary of contents

Page 1

... Email: info@lprs.co.uk Website: www.lprs.co.uk The RCU- radio remote controlled switching unit that will allow the remote operation of any appropriate electrical appliance that is required. The unit is constructed to commercial standards, giving the convenience of remote operation and in most cases the reduction in installation costs will exceed the cost of switching unit ...

Page 2

Low Power Radio Solutions Ltd The receiver unit must be securely mounted, using the mounting bracket provided, vertically with the aerial pointing upwards. Avoid positioning in close proximity to electronic equipment as interference from such equipment in certain circumstances could ...

Page 3

Low Power Radio Solutions Ltd To re-enter radio keys see “PROGRAMMING” section above Output Set-up NOTE: As viewed from the front with the aerial at the top, the dipswitches are in 1 block of 4. These are numbered from RIGHT ...

Page 4

... Low Power Radio Solutions Ltd Product Order Code LJ-RCU01 Additional Transmitter LJ-TX43-01 RCU01 4 11/08/2006 ...

Related keywords

LJ-TX43-01 datasheet
LJ-TX43-01 data sheet
LJ-TX43-01 pdf datasheet
LJ-TX43-01 component
LJ-TX43-01 part
LJ-TX43-01 distributor
LJ-TX43-01 RoHS
LJ-TX43-01 datasheet download