016198501 Tektronix, 016198501 Datasheet
016198501
Specifications of 016198501
016198501 Summary of contents
Page 1
... Rackmount Kits 075-0904-03 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service. www.tektronix.com *P075090403* 075090403 ...
Page 2
... Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved. ...
Page 3
Service Safety Summary Only qualified personnel should perform service procedures. Read this Service Safety Summary and the General Safety Summary before performing any service procedures. Do Not Service Alone. Do not perform internal service or adjustments of this product unless ...
Page 4
Service Safety Summary 2 016-1983-xx, 016-1985-xx, and 016-1988-xx Kits ...
Page 5
... Kit Description This document supports Tektronix DPO7000, DPO70000, DSA70000, and AWG7000 Series instruments. The rackmount kit is a collection of parts that, once installed, configure the instrument for mounting into a standard 19-inch equipment rack. Products DPO7000 Series DPO70000 Series DSA70000 Series AWG7000 Series ...
Page 6
Kit Description Warranted Characteristics When the instrument is installed according to the instructions in this document, the rackmounted instrument meets all warranted requirements listed in the instrument specification. Instruments mounted using methods other than those described in these instructions might ...
Page 7
Configuration 1 Air outlet 464.82 mm (18.30 in) Air inlet Figure 1: Clearance requirements 016-1983-xx, 016-1985-xx, and 016-1988-xx Kits Adjustable to 711.20 mm (28 in) Configuration 2 and 3 311.15 mm 266.7 mm (12.25 in) (10.5 in) Configurations Configuration 3 ...
Page 8
Kit Description 6 016-1983-xx, 016-1985-xx, and 016-1988-xx Kits ...
Page 9
... These instructions are for qualified service personnel who are familiar with servicing the product. If you need further details for disassembling or reassem- bling the product, refer to the appropriate product manual. Contact your nearest Tektronix, Inc., Service Center or Tektronix Factory Service for installation assistance. Remove Remove the handle and trim as shown in Figure 2 ...
Page 10
Installation Instructions Install Install the adapter bracket in your rack platform as shown in figures 3 and 4: NOTE. Configuration 3 has additional spacer rails. 1. Install the adapter bracket. NOTE. Install the adapter bracket only if you plan to ...
Page 11
Figure 4: Assembly installation (configurations 1 and 2 shown) 016-1983-xx, 016-1985-xx, and 016-1988-xx Kits Installation Instructions 9 ...
Page 12
Installation Instructions Reassemble 1. Remove the rack slides. See Figure 5. Figure 5: Removing the rack slides (configurations 1 and 2 shown) 10 Remove rack slides Use a screwdriver to release 016-1983-xx, 016-1985-xx, and 016-1988-xx Kits ...
Page 13
Attach the rack slides to your equipment rack. See Figure 6. Figure 6: Installing the rail slides 016-1983-xx, 016-1985-xx, and 016-1988-xx Kits Rack slides Left slide-out track. Use a bar nut if front rails are not tapped. Use two ...
Page 14
Installation Instructions 3. Install the rack platform in your equipment rack by inserting the platform Figure 7: Installation of rack plate assembly in rack (top view) (configurations 1 and 2 shown) WARNING. To avoid personal injury, prevent the instrument from ...
Page 15
Configuration 1 Figure 8: Installing the instrument on the rack plate 4. Install your instrument on the rack plate as shown in Figure 8. 5. Install the power cord. Provide access to a power plug or mains disconnect 6. Optionally ...
Page 16
Installation Instructions Figure 9: Installation of trim plate g End of document g 14 One trim plate can be attached to each side of the instrument as shown. 016-1983-xx, 016-1985-xx, and 016-1988-xx Kits ...