MCZCB1 MULTICOMP, MCZCB1 Datasheet

Enclosure Bezel

MCZCB1

Manufacturer Part Number
MCZCB1
Description
Enclosure Bezel
Manufacturer
MULTICOMP
Datasheet
1.MCGEA1.pdf (3 pages)

Specifications of MCZCB1

Accessory Type
Bezel
Body Material
ABS Plastic
For Use With
MCRECS Heat Sink Cases
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features:
Linc-Lugs:
• Aluminium extruded mounting bracket for fixing E-Case housings to walls, panels, vehicle bulkheads etc.
• Linc-Lug slides into any external dovetail feature on E-Case housings and is retained by the end plates.
• The silver lugs are strip silver anodized and are used with the silver E-Case enclosures that are anodized in the same way.
Non-Standard Lengths: Available but not with U-shaped slot.
Material: Aluminium 6063 T6 (HE9).
Finish: Silver anodized 5µm thickness. (Cut ends and inside of U-shaped slot are not anodized).
Weight: 15g. (Pair of lugs in plastic bag - MCLPS40).
Extrusion perimeter: 70mm.
Application Information: Linc-Lug is secured as follows:
For cases length 40mm and 80mm, use Linc-Lugs of appropriate length, retain with the end plates. Drill a hole 2.6mm diameter
through the dovetail on the Linc-Lug the V-groove as a drill start. Slide the drilled lug to the desired position along enclosure. Drive a
No.4 x 1/4” posi-pan type-B self tapping screw into the drilled hole to security wedge the Linc-Lug in the dovetail slot. MCLPS40 lugs
are now available with screws pre-fitted. These are supplied as a pair in a plastic bag.
Bezels:
• Cosmetic end plate surrounds made of ABS plastic that are available in four sizes to suit the four extrusion profiles.
• The four end-plate mounting screws pass through the bezel, through the end-plate and into the extrusion.
• The screw heads are concealed by inserts which closely match the bezel.
• This gives a much-improved cosmetic appearance.
Application Information:
The bezels come with the four inserts attached to a sprue on the bezel. The sprue should be cut off the bezel using a sharp knife.
Similarly the inserts should be cut off the sprue. Care should be taken not to leave plastic pipes on the inserts that will prevent them
lying flush when later inserted in the bezel. Once inserted, the inserts are not intended to be removed, but actually it is possible to
remove them without damage by carefully using a pin.
Bezels have a few applications that are worth particular mention. It is usual to put script on the front plate of an electronics housing.
This can be done by screen printing the plates, but an alternative method is to reverse print the back side of a clear polycarbonate
sheet. This can be cut and stuck on the end plate. The bezel is used to conceal the cut edges. Another application of the bezels is to
conceal the edge of a gasket that would normally be visible sandwiched between the end plate and the extrusion.
Heat Sink Cases
Accessories
Linc-Lug
Bezels
Page 1
Gaskets
31/03/08 V1.1

MCZCB1 Summary of contents

Page 1

... Heat Sink Cases Accessories Linc-Lug Features: Linc-Lugs: • Aluminium extruded mounting bracket for fixing E-Case housings to walls, panels, vehicle bulkheads etc. • Linc-Lug slides into any external dovetail feature on E-Case housings and is retained by the end plates. • The silver lugs are strip silver anodized and are used with the silver E-Case enclosures that are anodized in the same way. ...

Page 2

... Gasket Set, IP65, For MCREAS Cases Gasket Set, IP65, For MCREBS Cases Gasket Set, IP65, For MCRECS Cases Gasket Set, IP65, For MCREDS Cases Linc Lug, 40mm, Pack 2 Linc Lug, 80mm, Pack 2 Part Number MCZAB1 MCZBB1 MCZCB1 MCZDB1 MCGEA1 MCGEB1 MCGEC1 MCGED1 MCLPS40 MCLPS80 Page 2 ...

Page 3

... Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. © Premier Farnell plc 2008. ...