HFBR-24E2Z Avago Technologies US Inc., HFBR-24E2Z Datasheet - Page 21

• Manufacturer Part Number: HFBR-24E2Z
• Description: LT RX SC PORT,Pb-Free
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-24E2Z

• Data Rate: 5MBd
• Voltage - Supply: 4.75 V ~ 5.25 V
• Applications: General Purpose
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Power - Minimum Receivable: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Electrical/Optical Characteristics -40 °C to + 85 °C unless otherwise specified
Fiber sizes with core diameter d 100 μm and NA d 0.35, 4.75 V d V
Dynamic Characteristics
-40 °C to +85 °C unless otherwise specified; 4.75 V d V
Notes:
1. 2.0 mm from where leads enter case.
2. 8 mA load (5 x 1.6 mA), RL = 560 :.
3. Typical data at T
4. D is the effective diameter of the detector image on the plane of the fiber face. The numerical value is the product of the actual detector di-
5. Measured at the end of 100/140 Pm fiber optic cable with large area detector.
6. Propagation delay through the system is the result of several sequentially-occurring phenomena. Consequently it is a combination of data-
7. As the cable length is increased, the propagation delays increase at 5 ns per meter of length. Data rate, as limited by pulse width distortion, is
21
Parameter
High Level Output Current
Low Level Output Voltage
High Level Supply Current
Low Level Supply Current
Equivalent NA
Optical Port Diameter
Parameter
Peak Optical Input Power Logic Level
HIGH
Peak Optical Input Power Logic Level
LOW
Propagation Delay LOW to HIGH
Propagation Delay HIGH to LOW
CAUTION: The small junction sizes inherent to the design of these components increase the components’ susceptibility to damage
from electrostatic discharge (ESD). It is advised that normal static precautions be taken in handling and assembly of these compo-
nents to prevent damage and/or degradation which may be induced by ESD.
ameter and the lens magnification.
rate-limiting effects and of transmission-time effects. Because of this, the data-rate limit of the system must be described in terms of time
differentials between delays imposed on falling and rising edges.
not affected by increasing cable length if the optical power level at the receiver is maintained.
A
= +25 °C, V
CC
= 5.0 Vdc.
Symbol
I
V
I
I
NA
D
Symbol
P
P
t
t
OH
CCH
CCL
PLHR
PHLR
OL
RH
RL
Min
Min
-25.4
2.9
-24.0
4.0
CC
d 5.25 V; BER d 10
Typ
5
0.4
3.5
6.2
0.50
400
Typ
65
49
CC
3
3
d 5.25 V
-9
Max
250
0.5
6.3
10
Max
-40
0.1
-9.2
120
-10.0
100
Units
μA
V
mA
mA
μm
Units
dBm pk
μW pk
dBm pk
μW pk
dBm pk
μW pk
ns
ns
Conditions
V
P
I
P
V
P
V
P
Conditions
O
T
I
I
T
P
Data Rate =5
MBd
O
OL
OL
A
A
R
R
R
R
P
R
O
CC
CC
= 8 m
< -40 dBm
> -24 dBm
< -40 dBm
> -24 dBm
= +25 °C,
= +25 °C,
= -21 dBm,
= 820 nm
= 18
= 8mA
= 8mA
= 5.25 V
= 5.25 V
Reference
Note 4
Reference
Note 5
Note 5
Note 6