AMMP-6408-TR2G Avago Technologies US Inc., AMMP-6408-TR2G Datasheet
AMMP-6408-TR2G
Specifications of AMMP-6408-TR2G
Related parts for AMMP-6408-TR2G
AMMP-6408-TR2G Summary of contents
Page 1
... AMMP-6408 GHz 1 W Power Amplifier in SMT Package Data Sheet Description The AMMP-6408 MMIC is a broadband W power amplifier in a surface mount package designed for use in transmitters that operate in various frequency bands between 6 GHz and 8 GHz GHz, it provides 29 dBm of output power (P-dB) and small-signal gain from a small easy-to-use device. This MMIC optimized for linear operation with an output third order intercept point (OIP3 dBm. ...
Page 2
Absolute Maximum Ratings [1] Symbol Parameters V Positive Supply Voltage d V Gate Supply Voltage g I Drain Current d P Power Dissipation Input Power in T Maximum Operating Channel Temperature ch, max T Storage Case Temperature stg T Maximum Assembly Temp (20 sec. max.) max Notes: . Operation in excess of any one of these conditions may result in permanent damage to this device. 2. Combinations of supply voltage, drain current, input power, and output power shall not exceed PD. 3. When operating at this condition with a base plate temperature of 85°C, the median time to failure (MTTF) is significantly reduced. 4. These ratings apply to each individual FET. ...
Page 3
Typical Performances (Data Obtained from 3.5-mm Connector Based Test Fixture, and This Data is Including Connecter Loss, and Board Loss 25° 650 mA ...
Page 4
IM3 (dBc) Ids (mA) -20 -30 -40 -50 -60 -70 - SCL (dBm) Figure 7. Typical IM3 level and Ids vs. single carrier output level at 6 GHz 0 -10 ...
Page 5
S11_20 -20 S11_-40 S11_85 - FREQUENCY (GHz) Figure 13. Typical S11 over temperature 0 -5 -10 -15 S22_20 -20 S22_-40 S22_85 - FREQUENCY (GHz) Figure 15. Typical S22 ...
Page 6
Typical Scattering Parameters , (T = 25° Freq S11 [GHz] dB Mag Phase 6 -3.83 0.64 -7.36 7 -4.33 0.6 -37.59 8 -4.35 0.6 -57.25 9 -2.87 0.72 -67.80 0 -2.8 0.78 -8.97 -.88 0.8 -99.66 2 -2.85 ...
Page 7
... DC quiescent biasing condition at Vds = Ids = 650 mA, Vgg = - V , typical gate terminal current is approximately 0.3mA active biasing technique is selected for the AMMP6408 MMIC PA DC biasing, the active biasing circuit must have more than 0-times higher internal current that the gate terminal current optional output power detector network is also pro- vided ...
Page 8
800 µ 800 µ Figure 17. Simplified schematic for the MMIC die 800 µm 50 10K 50 800 µ ...
Page 9
RF INPUT -0 µF 100 pF 100 pF Note: . Vdd may be applied to either Pin 2 or Pin 6. 2. Vgg may be applied to either Pin or Pin 7. Figure 18. Schematic for recommended Bias circuitry 20 18 |Icomp (I_METER.AMP1.0)| (mA) 16 Diode_current ...
Page 10
... Recommended SMT Attachment for 5x5 Package The AMMP Packaged Devices are compatible with high volume surface mount PCB assembly processes. The PCB material and mounting pattern, as defined in the data sheet, optimizes RF performance and is strongly recommended. An electronic drawing of the land pattern is available upon request from Avago Sales & Application Engineering. Figure 21. Suggested PCB Land Pattern and Stencil Layout Figure 22 ...
Page 11
... Ordering Information MELTING POINT = 218 C AMMP-6408 Part Number Ordering Information Part Number AMMP-6408-BLKG COOLING AMMP-6408-TRG 200 250 300 AMMP-6408-TR2G 0.011 (0.28) 0.126 0.059 (3.2) (1.5) 0.100 (2.54) 0.029 (0.75) 0.016 (0.40) B SIDE VIEW 0.100 (2.54) DIMENSIONAL TOLERANCE: 0.002" (0.05 mm) ...
Page 12
... For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2008 Avago Technologies. All rights reserved. AV02-0243EN - October 20, 2008 AMMP XXXX ∅1.55 ± 0.05 R 0.50 TYP. ...