AFBR-703SDDZ Avago Technologies US Inc., AFBR-703SDDZ Datasheet - Page 10
![SFP+ 850nm 1/10GbE SR MMF,Gen2 STD](/photos/40/32/403227/av02-1967en_sml.jpg)
AFBR-703SDDZ
Manufacturer Part Number
AFBR-703SDDZ
Description
SFP+ 850nm 1/10GbE SR MMF,Gen2 STD
Manufacturer
Avago Technologies US Inc.
Series
-r
Datasheet
1.AFBR-703SDDZ.pdf
(22 pages)
Specifications of AFBR-703SDDZ
Data Rate
10.312Gbd
Wavelength
850nm
Applications
Ethernet
Voltage - Supply
3.135 V ~ 3.465 V
Connector Type
LC Duplex
Mounting Type
SFP+
Optical Fiber Type
TX/RX
Data Transfer Rate
10313MBd
Optical Rise Time
0.028ns
Optical Fall Time
0.028ns
Operating Temperature Classification
Commercial
Peak Wavelength
860nm
Package Type
SFP
Operating Supply Voltage (min)
3.135V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.465V
Output Current
20mA
Operating Temp Range
0C to 70C
Mounting
Snap Fit To Panel
Pin Count
20
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 5. Low Speed Signal Electrical Characteristics
The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted.
Typical values are for Tc = 40°C. VccT and VccR = 3.3 V.
Parameter
Module Supply Current
Power Dissipation
TX_FAULT, RX_LOS
TX_DISABLE
Notes:
1. Supply current includes both VccT and VccR connections.
2. Measured with a 4.7 k: load to VccHost.
3. TX_DISABLE has an internal 4.7 k: to 10 k: pull-up to VccT
Table 6. High Speed Signal Electrical Characteristics
The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted.
Typical values are for Tc = 40°C. VccT and VccR = 3.3 V.
Parameter
Tx Input Differential Voltage, |(TD +) - (TD-)|
Tx Input AC Common Mode Voltage Tolerance
Tx Input Differential S-parameter (100 : Ref.)
Tx Input Differential to Common
Mode Conversion (25 : Ref.)
Rx Output Differential Voltage, |(RD +) - (RD-)|
Rx Output Termination Mismatch @ 1MHz
Rx Output AC Common Mode Voltage
Rx Output Output Rise and Fall Time
(20% to 80%)
Rx Output Total Jitter
Rx Output 99% Jitter
Rx Output Differential S-parameter (100 : Ref.)
Rx Output Common Mode Reflection
Coefficient (25 : Ref.)
Receiver Output Eye Mask
Notes:
1. Internally AC coupled and terminated (100 Ohm differential).
2. Internally AC coupled but requires an external load termination (100 Ohm differential).
3. Maximum reflection coefficient is expressed as SDD11=Max(-12+2*sqrt(f ) , -6.3+13*log10(f/5.5)), for f in GHz.
4. Maximum reflection coefficient is expressed as SDD22=Max(-12+2*sqrt(f ) , -6.3+13*log10(f/5.5)), for f in GHz.
5. The RMS value is measured by calculating the standard deviation of the histogram for one UI of the common mode signal.
6. TJ conditions per SFF-8431.
10
Symbol
I
P
I
V
V
V
CC
OH
Symbol
V
SDD11
SCD11
Vo
'Z
tr, tf
TJ
DJ
SDD22
SCC22
DISS
OL
IH
IL
I
m
Minimum
180
300
28
Minimum
- 50
-
2.0
-0.3
0.3
Typical
Typical
180
600
Maximum
Note 3
-10
850
5
7.5
0.70
0.332
0.42
Note 4
-6
-3
15
1200
Maximum
289
1000
+ 37.5
0.4
VccT + 0.3
0.8
Unit
mVpp
mV(RMS)
dB
dB
mVpp
%
mV(RMS)
ps
Ulp-p
Ulp-p
Ulp-p
dB
dB
dB
Notes
Note 1
0.01-11.1GHz
0.01-11.1 GHz
Note 1, 10 GBd
1.25 Gbd
Note 5
Note 6, 10 GBd
1.25 Gbd
Note 6
0.01-11.1GHz
0.01-2.5 GHz
2.5-11.1 GHz
See Figure 5a
Unit
mA
mW
PA
V
V
V
Notes
Note 1
Note 2
Note 3