5962-8978501PC Avago Technologies US Inc., 5962-8978501PC Datasheet - Page 9

• Manufacturer Part Number: 5962-8978501PC
• Description: NPN-Output Dc-Input Optocoupler,2-CHANNEL,500V ISOLATION,DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of 5962-8978501PC

• Voltage - Isolation: 1500VDC
• Number Of Channels: 2, Unidirectional
• Current - Output / Channel: 40mA
• Data Rate: 100KBd
• Propagation Delay High - Low @ If: 30µs @ 500µA
• Current - Dc Forward (if): 10mA
• Input Type: DC
• Output Type: Open Collector
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Notes:
1. GND Pin should be the most negative voltage at the detector side.
2. Output power is collector output power plus total supply power for
3. Derate I
4. Each channel.
5. CURRENT TRANSFER RATIO is defined as the ratio of output collector
6. I
7. All devices are considered two-terminal devices; measured between
8. Measured between each input pair shorted together and all output
9. Measured between adjacent input pairs shorted together for each
10. CM
9
Keeping V
lowest total I
the single channel device. For the dual channel device, output power
is collector output power plus one half the total supply power. For
the quad channel device, output power is collector output power
plus one fourth of total supply power. Derate at 1.66 mW/°C above
110°C.
current, I
crosstalk. I
I
all input leads or terminals shorted together and all output leads or
terminals shorted together.
connections for that channel shorted together.
multi-channel device.
can be sustained with the output voltage in the logic low state
(V
voltage that can be sustained with the output voltage in the logic
high state (V
OHX
F
= 10 mA.
O
L
< 0.8 V). CM
is the leakage current resulting from channel to channel optical
is the maximum rate of rise of the common mode voltage that
F
O
at 0.33 mA/°C above 110°C.
, to the forward LED input current, I
CC
F
= 2 µA for channel under test. For all other channels,
O
OH
as low as possible, but greater than 2.0 V, will provide
> 2.0 V).
H
over temperature.
is the maximum rate of fall of the common mode
F
, times 100%.
11. In applications where dV/dt may exceed 50,000 V/µs (such as
12. This is a momentary withstand test, not an operating condition.
13. Standard parts receive 100% testing at 25°C (Subgroups 1 and
14. Parameters tested as part of device initial characterization and
15. The HCPL-6730, HCPL-6731, and HCPL-673K dual channel parts
16. Not required for 6N140A, 6N140A/883B, HCPL-177K, HCPL-
17. Required for 6N140A, 6N140A/883B, HCPL-177K, HCPL-6750/51/5K,
a static discharge) a series resistor, R
protect the detector ICs from destructively high surge currents. The
recommended value is:
R
for single channel;
R
for dual channel;
R
for quad channel.
9). SMD and 883B parts receive 100% testing at 25,125, and -55°C
(Subgroups 1 and 9, 2 and 10, 3 and 11, respectively).
after design and process changes. Parameters guaranteed to limits
specified for all lots not specifically tested.
function as two independent single channel units. Use the single
channel parameter limits.
6750/51/5K, 8302401, and 5962-9800201 types.
8302401, and 5962-9800201 types.
CC
CC
CC
= ————— kΩ
= ————— kΩ
= ————— kΩ
0.15 I
0.3 I
0.6 I
1 (V)
1 (V)
1 (V)
F
F
F
(mA)
(mA)
(mA)
CC
, should be included to