LXHL-FW1C LUMILEDS, LXHL-FW1C Datasheet
![LED, HIGH BRIGHTNESS, WHITE, 1W, 40.5LM](/photos/22/75/227529/4552213_sml.jpg)
LXHL-FW1C
Specifications of LXHL-FW1C
Available stocks
Related parts for LXHL-FW1C
LXHL-FW1C Summary of contents
Page 1
Technical Datasheet DS23 power light source LUXEON Introduction LUXEON ® revolutionary, energy efficient and ultra compact new light source, combining the lifetime and reliability advantages of Light Emitting Diodes with the brightness of conventional lighting. LUXEON features one ...
Page 2
Mechanical Dimensions LUXEON Star Side Emitting Batwing Notes: 1. Slots in aluminum core PCB for mounting screw. 2. Electrical interconnection pads labeled on the aluminum core PCB with "+" and " " to denote positive and negative, ...
Page 3
LUXEON Star/C Batwing Notes: 1. Holes in aluminum core PCB for mounting screw. 2. Connector on board AMP type, code 2 179123 2 ; Mating connector—AMP receptacle housing assembly, code 173977 2. 3. Positive and negative pins ...
Page 4
... These new batwing emitters (LXHL BW02) are incorporated into LUXEON Star part numbers LXHL MWEC, LXHL MWEA LXHL NWE8, LXHL MW1D, LXHL MW1B and LXHL FW1C. ...
Page 5
... Minimum flux value for 470 nm devices. Due to the CIE eye response curve in the short blue wavelength range, the minimum luminous flux will vary over the Lumileds' blue color range. Luminous flux will vary from a minimum of 6 460 typical 480 nm due to this effect. Although the luminous power efficiency is lower in the short blue wavelength range, radiometric power efficiency increases as wavelength decreases ...
Page 6
Optical Characteristics at 350mA, Junction Temperature ...
Page 7
... Side Emitting Notes for Tables 3, 4 and 5: 1. Dominant wavelength is derived from the CIE 1931 Chromaticity diagram and represents the perceived color. Lumileds maintains a tolerance of ± 0.5nm for dominant wavelength measurements. 2. Royal Blue product is binned by radiometric power and peak wavelength rather than photometric lumens and dominant wavelength. Lumileds maintains a tolerance of ± ...
Page 8
... Royal Blue Red Red Orange Amber Notes for Table 6: 1. Lumileds maintains a tolerance of ± 0.06V on forward voltage measurements. 2. Dynamic resistance is the inverse of the slope in linear forward voltage model for LEDs. See Figures 3a and 3b. Measured between 25°C ≤ T ≤ 110° LUXEON Star DS23 (3/06) Table 6 ...
Page 9
... Proper current derating must be observed to maintain junction temperature below the maximum. For more information, consult the LUXEON Design Guide, available upon request. 2. LEDs are not designed to be driven in reverse bias. Please consult Lumileds' Application Brief AB11 for further information reduction in maximum storage and operating temperature is required due to the acrylic optic. ...
Page 10
... Wavelength Characteristics, T 1.0 0.8 0.6 0.4 0.2 0.0 350 Figure 1c. White Color Spectrum of Typical Warm White Part, Integrated Measurement. Applicable for LXHL MWGC and LXHL NWG8. Light Output Characteristics 150 140 130 120 110 100 Figure 2a. Relative Light Output vs. Junction Temperature for White, Warm White, Green, Cyan, Blue and Royal Blue. ...
Page 11
Forward Current Characteristics, T Note: Driving these high power devices at currents less than the test conditions may produce unpredictable results and may be subject to variation in performance. Pulse width modulation (PWM) is recommended for dimming effects. LUXEON Star ...
Page 12
Forward Current Characteristics, T Note: Driving these high power devices at currents less than the test conditions may produce unpredictable results and may be subject to variation in performance. Pulse width modulation (PWM) is recommended for dimming effects. Figure 4a. ...
Page 13
Current Derating Curves Star, Star/C, Star/IDC 400 350 300 250 200 150 100 50 Figure 5a. Maximum Forward Current vs. Ambient Temperature. Derating based on T 400 350 300 250 200 150 100 50 Figure 5b. Maximum Forward Current vs. ...
Page 14
Current Derating Curves Star/O 400 350 300 250 200 150 100 Figure 5d. Maximum Forward Current vs. Ambient Temperature. Derating based on T and T 400 350 300 250 200 150 100 Figure 5e. Maximum Forward Current vs. Ambient Temperature. ...
Page 15
... Distributor or Lumileds sales representative. Batwing Radiation Pattern (without optics) 100 LUXEON Star White (LXHL MW1C, LXHL MW1A, LXHL MW1E) and Warm White (LXHL MWGC). 100 Figure 6b. Typical Representative Spatial Radiation Pattern for LUXEON Star Green, Cyan, Blue, Royal Blue and White. ...
Page 16
... Figure 6d. Typical Representative Spatial Radiation Pattern for LUXEON Star Red and Amber (LXHL BD01 and LXHL BL01). 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% Figure 6e. Typical Representative Spatial Radiation Pattern for LUXEON Star Red, Red Orange and Amber (LXHL BD03, BH03 and BL03). Lambertian Radiation Pattern (without optics) 100 Figure 7a ...
Page 17
Lambertian Radiation Pattern (without optics), Continued 100 Figure 7b. Typical Representative Spatial Radiation Pattern for LUXEON Star White Green, Cyan, Blue and Royal Blue. Side Emitting Radiation Pattern (without optics) Figure ...
Page 18
... Lifetime for solid state lighting devices (LEDs) is typically defined in terms of lumen maintenance—the percentage of initial light output remaining after a specified period of time. Lumileds projects that LUXEON products will deliver on average 70% lumen maintenance at 50,000 hours of operation. This performance is based on independent test data, Lumileds historical data from tests run on similar material systems, and internal LUXEON reliability testing. This projection is based on constant current 350 mA operation with junction temperature maintained at or below 90° ...
Page 19
... LEDs and systems are enabling new applications and markets in the lighting world. ©2006 Philips Lumileds Lighting Company. All rights reserved. Product specifications are subject to change without notice. Luxeon is a registered trademark of the Philips Lumileds Lighting Company in the United States and other countries. Philips Lumileds may make process or ...