10-1109.1329 EAO, 10-1109.1329 Datasheet - Page 30
![LAMP, INCANDESCENT, SLIDE, 12V](/photos/22/65/226517/4223021_sml.jpg)
10-1109.1329
Manufacturer Part Number
10-1109.1329
Description
LAMP, INCANDESCENT, SLIDE, 12V
Manufacturer
EAO
Datasheet
1.10-1106.1369.pdf
(60 pages)
Specifications of 10-1109.1329
Supply Voltage
12V
Base Type
Telephone Slide
Bulb Size
T-5.5
Average Bulb Life
5000h
Lead Style
Telephone Slide, T-5.5
Current Rating
100mA
Forward Voltage
12V
Lens Style
Tubular
Lamp Base Type
Telephone Slide
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Technical Data
Approvals
>
Switching system
Material
Mechanical characteristics
0
Actuator with low level switching element
Climate resistance
Damp heat state as per EN IEC 60068-2-30
Damp heat cyclic as per EN IEC 60068-2-78
Approbations
CB (IEC 61058)
CSA
ENEC (EN 61058)
Germanischer Lloyd
UL
Declaration of conformity
CE
This low level switching element was designed for switching low
powers in electronic circuits. The mechanism assures reliable
switching of loads ranging from a few μA/μV up to 100 mA/42 VAC/
DC.
Single-break momentary contact, as normally open or normally
closed with 4 independent points of contact. 2 momentary contacts
per switching element; combination of normally open and normally
closed is possible.
Special features are the long life, extremely short rebound time and
stable contact resistance.
Material of contact
Gold plated
Switch housing
Polysulfone, heat-resistant and self-extinguishing
Actuator housing
Polyamide
Terminals
The universal terminals permit these units to be mounted on printed
circuit boards (PCB). These terminals can also be used as
soldering or plug-in terminals.
For these terminals we can also supply a plug-in base which, when
soldered on to the board, enables the switch to be plugged in.
Soldering terminal:
Max. wire diameter 2 wires of 1 mm
Max. wire cross-section of stranded cable 2 x 0.75 mm²
Plug-in terminal: 2.0 x 0.5 mm.
Actuating torque
Measured at the key or lever of the keylock- or selector switch
2.5 Ncm ... 5.5 Ncm, depending on the number of switching
elements
Actuating force
3 ... 4 N, depending on the number of switching elements
Actuating travel
Illuminated pushbutton : 3 mm
Switch actuator 2 positions:
Momentary action
Maintained action
28
07.2009
1 x ca. 42° deflection momentary action
1 x ca. 90° deflection maintained action
Electrical characteristics
Environmental conditions
>
Buzzer system
Material
Mechanical characteristics
Electrical characteristics
Buzzer
Rebound time
typical <100 μs
Mechanical lifetime
Momentary action 5 million cycles of operation
Maintained action 1 million cycles of operation
Contact resistance
New state ≤50 mΩ as per DIN IEC 60512-2-4
Electrostatic discharge (ESD)
Keylock switch 15 kV
Switch rating
10 μA, 100 μV to 100 mA at 42 VAC/VDC
Electric strength
3000 VAC, 50 Hz, 1 min. between all terminals and earth, as per EN
IEC 61058-1-15
Protection class
II
Storage temperature
-40 °C ... +85 °C
Service temperature
-25 °C ... +55 °C
For indicators and illuminated pushbuttons mounted as a block,
make sure the heat can escape freely.
Protection degree
as per EN IEC 60529
front side IP 67
Shock resistance
(semi-sinusoidal)
max. 150 m/s², pulse width 11 ms, 3-axis, as per EN IEC 60068-2-
27
System
Piezo disc
Alarm buzzer case
Polyamide
Front cap
Plastic Polyamide
Metal Nickel-plated brass (sea-water proof)
Terminals
Plug-in terminal 2.8 x 0.5 mm
Frequency (tone)
approx. 2.8 kHz continuous tone only
14