FL124BPIR ETERNA, FL124BPIR Datasheet - Page 3

• Manufacturer Part Number: FL124BPIR
• Description: FLOODLIGHT, 24W, INC PIR, LOW ENERGY
• Manufacturer: ETERNA

Specifications of FL124BPIR

• Light Source: Fluorescent
• Length: 135mm
• Width: 210mm
• Depth: 100mm
• Ip/nema Rating: IP44
• Svhc: No SVHC (15-Dec-2010)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Installation Instructions and Care
The detection range of the unit may alter with changes
in ambient temperature.
To avoid damage to the PIR unit, do not aim the
sensor towards the sun.
To avoid nuisance triggering, the sensor should be
directed away from heat sources such as barbecues,
air-conditioners, other outside lighting, moving cars
and flue vents.
Do not connect to circuits with other light fittings or
appliances such as large fans, washing machines,
fluorescent lights etc. that may cause false triggering
through spikes generated in the mains supply.
Do not aim towards reflective surfaces such as smooth
white walls, swimming pools, etc.
Before selecting a place to install your floodlight you
should note that movement across the scan area is
more effective than movement directly towards or
away from the sensor (refer Fig.1B). When walking
directly towards or away from the sensor rather
than across, the apparent detection range will be
substantially reduced (refer Fig. 1C).
Do not attempt to modify the light or PIR sensor unit,
there are no user serviceable parts inside.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation there
are electrical tests that should be carried out: these
tests are specified in the Wiring Regulations (BS7671)
referred to in the Building Regulations. If in doubt,
consult a qualified electrician.
Installation
1.
2.
���� ���� ����
Choose the location for your new floodlight giving
consideration to all of the conditions listed above.
Loosen the screws at each end of the fixing
bracket and remove it. Note the position of each
��� � ���
������
���� ���� ��������� ����
��
��
���� ���� ���
���
�������
�
���
3
3.
5.
6.
7.
8.
9.
10. Undo the screws and lift off the cable clamp.
11. Undo and remove the cable entry nut and gland.
12. If necessary, pierce the gland making a hole
13. Thread your supply cable through the nut and
14. Make the connections to your mains supply as
15. Replace the cable grip and connection box cover
16. Using a cross-headed screwdriver, undo the
17. Fit the fluorescent lamp by pressing straight into
18. Replace the diffuser and tighten the screws
19. Restore the power and switch on.
4. Prepare your mounting surface as appropriate for
of the washers, it is important to fit them in the
correct order (see Fig. 2)
Using the fixing strap as a template, mark the
position for the fixing holes on your mounting
surface.
your chosen fixings (not supplied). Use a spirit
level to ensure the fitting will be level.
Secure the strap in place.
Fit the floodlight back onto the fixing strap and
replace the screws.
Before tightening the screws at the ends of the
fixing strap, adjust the position of the floodlight to
give the desired area of illumination.
Tighten the screws to lock your floodlight in
position.
Undo the four screws in the connection box cover
and remove it, take care not to lose any of the
screws or the sealing gasket.
just large enough for your supply cable to pass
through so that the gland makes a tight seal
around it.
gland and into the connection box.
described in the “Read this first” section.
ensuring that the cable is held securely and the
gasket is correctly positioned.
screws that secure the diffuser and allow to hang
down.
the lampholder.
making sure that the waterproof gasket is correctly
positioned and compressed.