YD630NM ETERNA, YD630NM Datasheet
![EMERGENCY LIGHT, NON-MAINT, 8W](/photos/22/62/226242/sr0660205-40_sml.jpg)
YD630NM
Manufacturer Part Number
YD630NM
Description
EMERGENCY LIGHT, NON-MAINT, 8W
Manufacturer
ETERNA
Datasheet
1.YD630NM.pdf
(2 pages)
Specifications of YD630NM
Length
345mm
Width
120mm
Depth
75mm
Ip/nema Rating
IP65
Svhc
No SVHC (15-Dec-2010)
Base Type
300mm T5 Fluorescent
External Depth
75mm
External Length / Height
345mm
External Width
120mm
Lamp Base Type
300mm T5 Fluorescent
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Cleaning:
>
Lamp replacement:
>
>
>
>
>
>
Replacement lamp type:
Wattage:
Type:
Replacement battery type:
2.4V Ni-Cad
7030-0621
Eventually, you may want to replace this light fitting:
When your light fitting and or battery pack come to the end of their life or you choose to update or
upgrade the fitting by replacing it, please do not dispose of it with your normal household waste, please
recycle where facilities exist. When you need to dispose of this fitting, check with your retailer or local
authority for suitable options. New regulations will encourage the recycling of Waste from Electrical and
Electronic Equipment ( European “WEEE Directive” effective August 2005 ).
If you experience problems:
If your light is defective or develops a fault, please return it to the place where you bought it. You can call our Helpline
for advice. The Helpline will gladly give advice on any aspect of any Eterna Lighting product but may not be able to
give specific instructions regarding individual installations.
If in doubt, consult a qualified electrician.
Help line:
Tel: 01933 673 144
For answers to frequently asked questions ( FAQs ) and other information visit our web-site
www.eterna-lighting.co.uk
Clean this light fitting only with a soft dry cloth—Do
not use any chemical or abrasive cleaners.
Switch off the electricity at the mains.
Remove the diffuser.
Twist and withdraw the tube.
Insert new tube.
Restore the power and perform operation check.
Replace diffuser.
8 W
T5 fluorescent tube
Fax: 01933 678 083
Email: sales@eterna-lighting.co.uk
Battery replacement:
If after routine operation check, the lamp does not
remain lit for the three hour period, a new battery pack
may be required.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10) Plug battery pack into circuit board.
11) Close and secure gear tray
12) Replace diffuser.
13) Restore power and allow to charge for 24 hours.
14) Perform full operation check and update test record.
Switch off the electricity at the mains.
Allow batteries to fully discharge then reconnect to
supply and allow to charge for 24 hours.
Test again for 3 hours, if light does not remain lit
change the battery pack as follows:
Remove the diffuser.
Remove the two screws indicated on the gear tray
and open the fitting.
Unplug the battery lead from the circuit board.
Remove the two screws in the top of the gear tray
beneath the lamp that secure the battery pack in
place and lift the battery pack out of the fitting.
Write current date on the new battery pack.
Fit new battery pack securing in place using the
screws removed from the old pack.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING
Specification:
Power
Continuous illumination
Battery
Recharge time
Over-discharge protection
Non-maintained emergency
PLEASE RETAIN FOR FUTURE REFERENCE
bulkhead light 8W
YOUR NEW FITTING
>3 hours @ 45Lm
YD630NM
2.4V 4.5Ah
Model(s)
~20 hours
- -
Yes
8W
BLF
EBLF
30.2%
17.7%
Related parts for YD630NM
YD630NM Summary of contents
Page 1
... Tel: 01933 673 144 Fax: 01933 678 083 Email: sales@eterna-lighting.co.uk For answers to frequently asked questions ( FAQs ) and other information visit our web-site www.eterna-lighting.co.uk Non-maintained emergency bulkhead light 8W Model(s) YD630NM Specification: Power 8W Continuous illumination >3 hours @ 45Lm Battery 2.4V 4.5Ah Recharge time ...
Page 2
... During this period all fittings in doubt, consult a qualified electrician. should be examined visually to ensure that they are functioning correctly. At the end of the test period the supply shall be restored and all indicator lamps or devices Installation: checked to ensure that the normal supply has been restored. ...