REM3RD ETERNA, REM3RD Datasheet

REM3RD

Manufacturer Part Number

REM3RD

Description

EMERGENCY BULKHEAD, RECESSED, WHITE

Manufacturer

ETERNA

Datasheet

1.REM3RD.pdf (2 pages)

Specifications of REM3RD

Length

410mm

Width

125mm

Depth

90mm

Svhc

No SVHC (15-Dec-2010)

Approval Bodies

BS EN 60598

Base Type

T5 Fluorescent 8W

Colour

White

Supply Voltage

240V

Lamp Base Type

T5 Fluorescent 8W

Rohs Compliant

Yes

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (169Kb)

If you experience problems...

If your light is defective or develops a fault, please return it to the place where you bought it. You can call our

Helpline for advice. The Helpline will gladly give advice on any aspect of any Eterna Lighting product but may not be

able to give speciﬁc instructions regarding individual installations. If in doubt, consult a qualiﬁed electrician.

Help Line - Tel: 01933 673 144

For all other information visit our website www.eterna-lighting.co.uk

Installation Instructions and Care

Periodic testing should be carried out monthly by

simulating a failure of supply, causing the ﬁtting to be

energised from its battery. Interruption of the supply

should be carried out by the operation of a local

keyswitch or other isolation device. During this period

all ﬁttings should be examined visually to ensure that

they are functioning correctly. At the end of the test

period the supply shall be restored and all indicator

lamps or devices checked to ensure that the normal

supply has been restored.

The duration of the simulated failure shall be:-

Each Month: Isolate the power supply and check the

light is illuminated. This test should last for no more

than 45 minutes. Endorse the test record form supplied.

Every Six Months: Isolate the power supply and check

that the light is still illuminated after 1 hour. Endorse

the test record form.

Once Each Year: Isolate the power supply and check

that the light is still illuminated after 3 hours. Endorse

the test record form.

Important Notes: Please keep this instruction booklet

and test record in a safe place. A ﬁre ofﬁcer or other

authorised person may want to see your record of

inspection and testing.

The ballast and control gear must be operated only

within the enclosure supplied. The gear must not be

operated outside of the enclosure.

The battery charging circuit and DC ballast are

separated from the mains by at least basic (single layer)

insulation.

When energised by a constant mains supply, the battery

will be constantly charged whether or not the lamp is

illuminated. On failure of the constant mains supply,

the ﬁtting will switch automatically using transistorised

switching from battery charging to battery discharge

powering the lamp whether or not the lamp was

illuminated before the power failure. Both the mains

and battery supplies incorporate fuse protection: see

ﬁtting for location and rating.

Safety Markings

Cleaning

Clean this light ﬁtting only with a soft dry cloth

Do not use any chemical or abrasive cleaners.

Operation Checks

Fax: 01933 678 083

Email: sales@eterna-lighting.co.uk

Lamp Replacement

1. Switch off the electricity at the mains.

2. Remove the diffuser. Note: When diffuser is

3. Twist and withdraw the tube.

4. Insert new tube.

5. Restore the power and perform operation check.

6. Replace diffuser.

Replacement Lamp Type

Wattage: 8W

Type: T5 Fluorescent Tube

Replacement Battery Type

2.4V Ni-Cad 2 x D cells

7030-0621

Battery Replacement

If after routine operation check, the lamp does not

remain lit for the three hour period, a new battery pack

may be required.

1. Switch off the electricity at the mains.

2. Allow batteries to fully discharge then reconnect to

3. Test again for 3 hours, if light does not remain lit

4. Remove the diffuser.

5. Remove the two screws indicated on the gear tray

6. Unplug the battery lead from the circuit board.

7. Remove the two screws in the top of the gear tray

8. Write current date on the new battery pack.

9. Fit new battery pack securing in place using the

10. Plug battery pack into circuit board.

11. Close and secure gear tray.

12. Replace diffuser.

13. Restore power and allow to charge for 24 hours.

14. Perform full operation check and update test

removed, ﬁtting is not ﬁxed in place.

supply and allow to charge for 24 hours.

change the battery pack as follows:

and open the ﬁtting.

beneath the lamp that secure the battery pack in

place and lift the battery pack out of the ﬁtting.

screws removed from the old pack.

record.

IMPORTANT! Please read these instructions before installing your new ﬁtting.

REM3RDDCR/REM3RDD - Slotted Reeded Diffuser with Exit Sign

Model: Recessed Emergency Fitting

REM3MDD/REM3MDDCR - Slotted Metal Plate with Exit Sign

SAFETY AND INSTALLATION

REM3RD/REM3RDCR - Reeded Diffuser

Please retain for future reference.

INSTRUCTIONS

Pack Contents

1 x Recessed Emergency Fitting

1 x Front Panel c/w either:

• Reeded Diffuser

• Hanging Sign Panel

• Hanging Sign Panel and Reeded Diffuser

Related parts for REM3RD

REM3RD Summary of contents

Page 1

... For all other information visit our website www.eterna-lighting.co.uk SAFETY AND INSTALLATION INSTRUCTIONS Model: Recessed Emergency Fitting REM3RDDCR/REM3RDD - Slotted Reeded Diffuser with Exit Sign REM3MDD/REM3MDDCR - Slotted Metal Plate with Exit Sign REM3RD/REM3RDCR - Reeded Diffuser IMPORTANT! Please read these instructions before installing your new ﬁtting. ...

Page 2

... As the buyer, installer and/or user of this product it is circuit (protected with Amp MCB or fuse your own responsibility to ensure that this ﬁtting is ﬁt for the purpose for which you have intended it. Eterna fused spur (with a 3 Amp fuse) via a fused connection unit. ...

Related keywords

REM3RD datasheet
REM3RD data sheet
REM3RD pdf datasheet
REM3RD component
REM3RD part
REM3RD distributor
REM3RD RoHS
REM3RD datasheet download