AFBR-707SDZ Avago Technologies US Inc., AFBR-707SDZ Datasheet
AFBR-707SDZ
Specifications of AFBR-707SDZ
Related parts for AFBR-707SDZ
AFBR-707SDZ Summary of contents
Page 1
... SFP+ Transceiver for Legacy MMF links on OM1, OM2, OM3 fiber up to 220m Data Sheet Description The Avago AFBR-707SDZ transceiver is part of a family of SFP+ products. This transceiver utilizes Avago’s 1310 nm FP and PIN Detector technology to provide an IEEE 10Gb Ethernet design compliant with the 10GBASE-LRM stan- dard ...
Page 2
... Predictive Failure Identifi- cation, Compliance Prediction, Fault Isolation and Com- ponent Monitoring. Predictive Failure Identification The AFBR-707SDZ predictive failure feature allows a host to identify potential link problems before system perfor- mance is impacted. Prior identification of link problems enables a host to service an application via “fail over” ...
Page 3
... DC balanced. Transmit Disable (TX_DISABLE) The AFBR-707SDZ accepts an LVTTL compatible trans- mit disable control signal input which shuts down the transmitter optical output. A high signal implements this function while a low signal allows normal transceiver op- eration ...
Page 4
... AFBR-707SDZ. All mechanical ad- justments are made at the factory prior to shipment. Tampering with, modifying, misusing or improperly han- dling the AFBR-707SDZ will void the product warranty. It may also result in improper operation and possibly over- stress the laser source. Performance degrada tion or de- vice failure may result ...
Page 5
... Due to its shielded design, the EMI immunity of the AFBR-707SDZ exceeds typical industry standards. Eye Safety The AFBR-707SDZ provides Class 1 (single fault tolerant) eye safety by design and has been tested for compliance with the requirements listed in Table 1. The eye safety circuit continuously monitors the optical output power ...
Page 6
Table 1. Regulatory Compliance Feature Test Method Electrostatic Discharge (ESD) MIL-STD883C Method 3015.4 to the Electrical Contacts JEDEC DESD22-A11-4-B Electrostatic Discharge (ESD) IEC 61000-4-2 to the Duplex LC Receptacle Life Traffic ESD Immunity IEC 61000-4-2 Life Traffic ESD Immunity IEC ...
Page 7
TX_DISABLE TX_FAULT SERDES IC PROTOCOL IC with EDC Function in Receive Path LOSS OF SIGNAL RS0 RS1 MODULE DETECT SCL SDA Figure 2. Typical application configuration 7 4 kΩ 4.7 uH Host DCR=0.15 0.1 μF Vcc 4.7 ...
Page 8
Table 2. Contact Description Contact Symbol Function/Description 1 VeeT Transmitter Signal Ground 2 TX_FAULT Transmitter Fault (LVTTL-O) – High indicates a fault condition 3 TX_DISABLE Transmitter Disable (LVTTL-I) – High or open disables the transmitter 4 SDA Two Wire Serial ...
Page 9
Table 3. Absolute Maximum Ratings Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions. It should not be assumed that ...
Page 10
Table 5. Low Speed Signal Electrical Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Parameter Module Supply Current Power Dissipation TX_FAULT, RX_LOS TX_DISABLE Notes: 1. Supply current includes both VccT and VccR connections. 2. ...
Page 11
MODULE FAILS 0.05 0.04 MODULE PASSES 0.03 0.02 pre-cursor post-cursor split-symmetrical 0.01 host (informative) 0 -0.5 0 0.5 dWDP Figure 4. RN and dWDP compliance regions for LRM [proposed] Table 7. Two-Wire Interface Electrical Characteristics Parameter Symbol Host ...
Page 12
Optical Specifications Parameter Transmitter Signaling Speed - nominal Signaling Speed variation from nominal Center Wavelength RMS Spectral Width at 1260 nm RMS Spectral Width between 1260 nm and 1300 nm RMS Spectral Width between 1300 nm and 1355 nm Launch ...
Page 13
Maximum allowed rms spectral width 0 1300 1320 1260 1280 Wavelength (nm) Figure 5a. 10GBASE-LRM Transmitter spectral limits 1 Maximum: 0.5 dBm Extinction ratio, minimum 0 (3.5 dB Minimum: -6.5 ...
Page 14
Table 10. Control Functions: Low Speed Signals Timing Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Parameter TX_DISABLE Assert Time TX_DISABLE Negate Time Time to initialize, including reset of TX_FAULT TX_FAULT Assert Time TX_DISABLE ...
Page 15
Table 11. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Parameter Transceiver Internal Temperature Transceiver Internal Supply Voltage Transmitter Laser DC Bias Current Transmitted Average Optical Output ...
Page 16
... Addresses 63 and 95 are checksums calculated (per SFF-8472) and stored prior to product shipment. 4. Addresses 68-83 specify the AFBR-707SDZ ASCII serial number and will vary on a per unit basis. 5. Addresses 84-91 specify the AFBR-707SDZ ASCII date code and will vary on a per date code basis. 16 ...
Page 17
... Transmitted average optical power (Tx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 5. Received average optical power (Rx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 6. Bytes 56-94 are not intended for use with AFBR-707SDZ, but have been set to default values per SFF-8472. 7. Byte checksum calculated (per SFF-8472) and stored prior to product shipment. ...
Page 18
... Indicates transceiver is powered and real time sense data is ready Ready) Notes: 1. The response time for soft commands of the AFBR-707SDZ is 100 msec as specified by SFF-8472. 2. Bit 6 is logic OR’d with the SFP TX_DISABLE input on contact 3; either asserted will disable the SFP+ transmitter. Table 16. EEPROM Serial ID Memory Contents – Alarms and Warnings (Address A2h, Bytes 112, 113, 116, 117) ...
Page 19
TCASE REFERENCE POINT LATCH COLOR BLACK: 10GBASELRM 6. Figure 7. Module drawing Label format Figure 8. Module label For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A ...