AFBR-703SDZ Avago Technologies US Inc., AFBR-703SDZ Datasheet
AFBR-703SDZ
Specifications of AFBR-703SDZ
Available stocks
Related parts for AFBR-703SDZ
AFBR-703SDZ Summary of contents
Page 1
... Ethernet, 850 nm, 10GBASE-SR, SFP+ Transceiver Data Sheet Description The Avago AFBR-703SDZ transceiver is part of a family of SFP+ products. This transceiver utilizes Avago’s 850nm VCSEL and PIN Detector technology to provide an IEEE 10Gb Ethernet design compliant with the 10GBASE-SR standard. The AFBR-703SDZ transceiver is designed to ...
Page 2
... Predictive Failure Identifi- cation, Compliance Prediction, Fault Isolation and Com- ponent Monitoring. Predictive Failure Identification The AFBR-703SDZ predictive failure feature allows a host to identify potential link problems before system perfor- mance is impacted. Prior identification of link problems enables a host to service an application via “fail over” redundant link or replace a suspect device, maintaining system uptime in the process ...
Page 3
... DC bal- anced. Transmit Disable (TX_DISABLE) The AFBR-703SDZ accepts an LVTTL compatible trans- mit disable control signal input which shuts down the transmitter optical output. A high signal implements this function while a low signal allows normal transceiver op- eration ...
Page 4
... AFBR-703SDZ. All mechanical ad- justments are made at the factory prior to shipment. Tampering with, modifying, misusing or improperly han- dling the AFBR-703SDZ will void the product warranty. It may also result in improper operation and possibly over- stress the laser source. Performance degrada tion or de- vice failure may result ...
Page 5
... EMI immunity of the AFBR-703SDZ exceeds typical industry standards. Eye Safety The AFBR-703SDZ provides Class 1 (single fault tolerant) eye safety by design and has been tested for compliance with the requirements listed in Table 1. The eye safety circuit continuously monitors the optical output power ...
Page 6
Table 1. Regulatory Compliance Feature Test Method Electrostatic Discharge (ESD) MIL-STD-883C to the Electrical Contacts Method 3015.4 Electrostatic Discharge (ESD) IEC 61000-4-2 to the Duplex LC Receptacle Life Traffic ESD Immunity IEC 61000-4-2 Life Traffic ESD Immunity IEC 61000-4-2 Electromagnetic ...
Page 7
Tx_DISABLE Tx_FAULT SERDES IC PROTOCOL IC LOSS OF SIGNAL 4 kΩ MODULE DETECT SCL SDA Figure 2. Typical application configuration 0.1 μF 22 μ 0.1 μF 22 μF HOST BOARD SFP ...
Page 8
Table 2. Contact Description Contact Symbol Function/Description 1 VeeT Transmitter Signal Ground 2 TX_FAULT Transmitter Fault (LVTTL-O) – High indicates a fault condition 3 TX_DISABLE Transmitter Disable (LVTTL-I) – High or open disables the transmitter 4 SDA Two Wire Serial ...
Page 9
Table 3. Absolute Maximum Ratings Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions. It should not be assumed that ...
Page 10
Table 5. Low Speed Signal Electrical Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Typical values are for Tc = 40°C. VccT and VccR = 3.3 V. Parameter Module Supply Current Power Dissipation TX_FAULT, ...
Page 11
NORMALIZED TIME (UNIT INTERVAL) Figure 5a. Receiver Electrical Optical Eye Mask Definition Table 7. Two-Wire Interface Electrical Characteristics Parameter Symbol Host Vcc Range VccHTWI SCL and SDA SCL ...
Page 12
Table 8. Optical Specifications The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Typical values are for Tc = 40°C. VccT and VccR = 3.3 V. Parameter Transmitter Laser OMA output power Laser mean output power ...
Page 13
Table 9. Minimum Optical Modulation Amplitude Center RMS Spectral Width (nm) Wavelength Up to 0.05 to (nm) 0.05 0.1 840 to 842 -4.2 -4.2 842 to 844 -4.2 -4.2 844 to 846 -4.2 -4.2 846 to 848 -4.3 -4.2 848 ...
Page 14
Table 11. Control Functions: Two-Wire Interface Timing Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Parameter TX_DISABLE Assert Time TX_DISABLE Negate Time TX_FAULT Assert Time Rx_LOS Assert Time Rx_LOS Deassert Time Analog parameter data ...
Page 15
Table 12. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Typical values are for Tc = 40°C. VccT and VccR = 3.3 V. Parameter Transceiver Internal Temperature ...
Page 16
... Addresses 63 and 95 are checksums calculated (per SFF-8472) and stored prior to product shipment. 4. Addresses 68-83 specify the AFBR-703SDZ ASCII serial number and will vary on a per unit basis. 5. Addresses 84-91 specify the AFBR-703SDZ ASCII date code and will vary on a per date code basis. 16 ...
Page 17
... Transmitted average optical power (Tx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 5. Received average optical power (Rx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 6. Bytes 56-94 are not intended for use with AFBR-703SDZ, but have been set to default values per SFF-8472. 7. Byte checksum calculated (per SFF-8472) and stored prior to product shipment. ...
Page 18
... Indicates transceiver is powered and real time sense data is ready Ready) Notes: 1. The response time for soft commands of the AFBR-703SDZ is 100 msec as specified by SFF-8472. 2. Bit 6 is logic OR’d with the SFP TX_DISABLE input on contact 3; either asserted will disable the SFP+ transmitter. Table 16. EEPROM Serial ID Memory Contents – Alarms and Warnings (Address A2h, Bytes 112, 113, 116, 117) ...
Page 19
TCASE REFERENCE POINT LATCHCOLOR BLACK 6. Figure 7. Module drawing Figure 8. Module label For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of ...