338068-6 Tyco Electronics, 338068-6 Datasheet
338068-6
Specifications of 338068-6
Available stocks
Related parts for 338068-6
338068-6 Summary of contents
Page 1
... Electronics and its worldwide subsidiaries and affiliates. All international rights reserved It may not be disclosed to anyone, other than Tyco Tyco Electronics Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA *Trademark R6-76 (Rev. 07-01) DATE 28/10 /98 APVD M.Gosselink This specification is a controlled document and subject to change ...
Page 2
DIN-specifications. DIN 17662 Wrought copper alloys (tin-bronze); chemical composition DIN 17670 Plate, sheet and strip of wrought copper an copper alloys: mechanical properties 2.3 I.E.C. Specifications I.E.C. 512 Connectors used for frequencies below 3 MHz (Mc/s) I.E.C 68 ...
Page 3
Male-on-board connector Male-on-board connector assembly, consisting of a number of contact pins, press-fit in a moulded housing. 3.3.4 Male-on-wire connector Male-on-wire connector assembly, consisting of a number of contact with slotted beam section, press-fit in a moulded housing, ...
Page 4
Note: The Micro-MaTch male-on-wire connector is specifically designed to be disengaged from its counterpart by pulling the cable in the appropriate direction. 3.5 Ribbon cable and wire Specification 3.5.1 Ribbon cable specification The AMP Micro-MaTch connectors with IDC (insulation ...
Page 5
Current ( SMC Female Top Entry with Male On Wire A valid for Female Side Entry with Male On Wire SMD Female Top Entry with Male On Wire Paddle ...
Page 6
Test description 3.6.1. Examination of product Solderability for through hole 3.6.2. versions 3.6.3. Resistance to soldering heat for through hole versions Solderability for SMD 3.6.4. Resistance to Soldering Heat 3.6.5. for SMD Para. Test description Insulation resistance 3.6.6. 3.6.7. ...
Page 7
Termination resistance 3.6.9. SMC types 3.6.10. Termination resistance SMD types 3.6.11. Termination resistance paddle board. Test description 3.6.12 Contact retention in housing. Mechanical operation 3.6.13 Rev. F R6-77 (Rev. 07-01 ...
Page 8
Axial strength of wire termination 3.6.15 Tensile strength of termination. Engaging and separating force 3.6.16 Vibration 3.6.17 Push-in push out forces in a 3.6.18 PCB Connector insertion force in 3.6.19 PCB (only Paddle board) Connector extraction force out ...
Page 9
Test sequence 3.7.1 Female Top/Side Entry in combination with Male on Wire/Male On Board connector. Tests Testgroup 1 1. Visual examination 2. 3. Climatic sequence a) Dry heat b) Damp heat cyclic, first cycle c) Cold d) Damp Heat ...
Page 10
Tests 3. Visual examination Testgroup 8: 1. Visual examination 2. 3. Dry heat under cyclic current loading 4. 5. Visual examination Testgroup 9: 1. Visual examination 2. Pre-conditioning (24 hrs at lab. conditions Voltage proof 5. Climatic ...
Page 11
Testgroup 4: 1. Visual examination 2. Push-in and push out forces in a PCB 3. Visual examination Testgroup 5: 1. Visual examination 2. 3. Dry heat under cyclic current loading 4. 5. Visual examination Testgroup 6: 1. Visual examination ...
Page 12
Tests Testgroup 6: 1. Visual examination 2. Connector insertion force 3. Connector extraction force 4. Visual examination Testgroup 7: 1. Visual examination 2. 3. Dry heat under cyclic current loading 4. 5. Visual examination 3.7.4 Additional tests for Female ...
Page 13
Tests Testgroup 4: 1. Visual examination 2. Contact retention in housing 3. Visual examination Testgroup 5: 1. Visual examination 2. Solderability 3. Visual examination Testgroup 6: 1. Visual examination 2. Resistance to soldering heat 3. Visual examination 3.7.5 Additional ...
Page 14
Tests 3. Visual examination Testgroup 5: 1. Visual examination 2. Current load cyclic 3. Visual examination Testgroup 6: 1. Visual examination 2. 3. Voltage proof 4. Climatic sequence a) Dry heat b) Damp heat cyclic, first cycle c) Cold ...
Page 15
QUALITY ASSURANCE PROVISIONS 4.1 Qualification testing: 4.1.1 Sample selection: Samples shall be released in accordance with applicable instruction sheets. They shall be selected at random from production. At least 5 connectors of the 6 positions or at least 30 ...