IEG6-1-52-50.0-01-V AIRPAX, IEG6-1-52-50.0-01-V Datasheet
![CIRCUIT BREAKER, HYD-MAG, 1P, 240V, 50A](/photos/21/80/218034/4081184_sml.jpg)
IEG6-1-52-50.0-01-V
Specifications of IEG6-1-52-50.0-01-V
Related parts for IEG6-1-52-50.0-01-V
IEG6-1-52-50.0-01-V Summary of contents
Page 1
Introduction Single & Multi-Pole Rocker, Sealed Toggle Configurations Operating Characteristics Delay Curves Specifications Decision Tables IAG/IUG/IEG/CEG/LEG Magnetic Circuit Protectors 105 | 106 | | 109 | 114 116 | 117 | | 121 | 123 ...
Page 2
... INTRODUCTION The Airpax™ IAG/IUG/IEG/CEG/LEG magnetic circuit protectors provide low-cost power switching, reliable circuit protection and accurate circuit control for equipment in the international marketplace. IEG models meet IEC spacing requirements which is mandatory for equipment that must comply with IEC specifications 601 and 950 and VDE specifications 0804 and 0805 ...
Page 3
... Single Pole Mounting Detail +.010 -.000 .625 +.25 -.00 15.88 1.660 1.050 [ 42. 26. 0.156 [ 3.96 ] http://airpax.sensata.com/ SINGLE POLE CIRCUIT PROTECTOR 1.687 [ 42.85 ] 2.075 .690 [ 17. 52.71 ] MAX. .590 2X 6 – 32 THREAD [15.00] .140 [ 3.56 ] DEEP MAX. M3 ISO THD. OPTIONAL 2.000 .1.660 [ 50. ...
Page 4
... An auxiliary switch may be included in either or both poles, allowing you to mix SELV and hazardous voltages. Rugged screw-type terminals can be provided, in which case the designation would be IEG66. The IEGH offers a toggle handle for each pole. LEG type units are avavailable only in one or two pole configurations. ...
Page 5
... In order to meet UL listing requirements, the LEG/LEGH two pole model requires barriers. Available with a standard straight barrier or an optional “Z” type barrier. Standard Barrier Note: Tolerance ± .015 [.38] unless noted. Dimensions in brackets [ ] are millimeters. http://airpax.sensata.com – 32 THREAD 2X .590 .140 [ 3.56 ] DEEP [ 15 ...
Page 6
... Single Pole Mounting Detail for hole sizes and locations. .750 [19.05] Three Pole Single, Two & Three Pole 2.265 Max. 2X .156 [3.96] [ 57.53 ] 1.660 [42.16] 1.260 [32.00] .200 [5.08] ON .750 OFF [19.05] Panel Mounting Detail: Tolerance for Mtg. ±.005 [.13] unless noted. Detail “A” http://airpax.sensata.com/ ...
Page 7
... Only Airpax offers this new standard in user interface, providing additional peace of mind that guards alone can’t supply. ...
Page 8
... Single Pole Mounting Detail for hole sizes and locations. Note: Tolerance ± .015 [.38] unless noted. Dimensions in brackets [ ] are millimeters. Two Pole Three Pole 2.265 1.515 [ 57. 38.48 ] MAX. MAX. (Optional: Handle may be located in Pole 2 instead of Pole 1) Three Pole* Two Pole* .750 .750 .750 [ 19. 19. 19.05 ] http://airpax.sensata.com/ ...
Page 9
... The IEGS is offered in either flush or beveled versions pole packages, and with a handle per pole or per unit. The IEGS is UL Recognized, CSA Certified and VDE approved. 1.488 2.232 [ 37 ...
Page 10
... OFF OFF OFF DIM. “B” (SEE TABLE) DIM. “C” (SEE TABLE) Dimension “C”, inches [ mm ] 2.180 ± .005 [55.37 ± .13] .040 to .059 Panel Thickness [1.02 to 1.50] http://airpax.sensata.com/ 2.186 ± .011 [55.52 ± .28] .060 to .100 [1.52 to 2.54] ...
Page 11
... Metric screw terminals are M4 x 5mm (<=30A 5mm screw type (>30A). On VDE approved builds with screw terminals, external tooth lockwashers are supplied. On VDE approved builds with push-on terminals a soldered connection is required above 25 amperes. http://airpax.sensata.com/ .230 [ 5. ...
Page 12
... Note A) 1.380 [ 35.05 ] 1.530 [ 38.86 ] Dual Coil .230 2.52 MAX 64.00 ] (See Note A) .620 [ 15.75 ] 1.380 [ 35.05 ] 1.530 [ 38.86 ] Dual Coil Optional Barriers (IEG Only) .571 [ 14.50 ] 2.000 [ 50.80 ] Note: Tolerance ± .015 [.38] unless noted. Dimensions in brackets [ ] are millimeters. http://airpax.sensata.com/ ...
Page 13
... Max *CEG type units are available only with 51, 52, ,53 and 59 delays LEG type units are available only with 61, 62, 63 and 69 delays **135% minimum trip point for delays 71, 72, 73 and 79 http://airpax.sensata.com/ OPERATING CHARACTERISTICS Inrush Pulse Tolerance The following table provides a comparison of inrush ...
Page 14
... DELAY 62 0 100 150 200 300 400 500 600 700 800 900 125 PERCENT OF RATED CURRENT DELAY 69 0 100 150 200 300 400 500 600 700 800 900 125 PERCENT OF RATED CURRENT http://airpax.sensata.com/ 1000 1000 ...
Page 15
... PERCENT OF RATED CURRENT 10000 DELAY 52 1000 100 .01 .001 0 100 150 200 300 400 500 600 700 125 PERCENT OF RATED CURRENT http://airpax.sensata.com/ 10000 1000 100 .01 .001 0 100 150 200 800 900 1000 10000 1000 100 .01 .001 800 ...
Page 16
... DELAY 72 1000 100 001 0 100 150 200 300 400 500 600 700 800 135 PERCENT OF RATED CURRENT DELAY 79 100 001 0 100 150 200 300 400 500 600 700 800 135 http://airpax.sensata.com/ 900 1000 900 1000 ...
Page 17
... PERCENT OF RATED CURRENT 10000 DELAY 42 1000 100 .01 .001 0 100 150 200 300 400 500 600 700 125 PERCENT OF RATED CURRENT http://airpax.sensata.com/ 10000 1000 100 .01 .001 800 900 1000 0 100 150 200 10000 1000 100 .01 .001 800 ...
Page 18
... APPROxIMATE WEIGHT PER POLE ( POLES AVAILABLE) Ounces 2.2 RECOMMENDED TORQUE SPECIFICATIONS Component 6-32 Mounting Inserts M3 Mounting Screws 8-32 Screw Terminals M4 Terminal Screws 10-32 Screw Terminals M5 Screw Terminals 1 Mounting Bushing Where applicable, mechanical support must be provide to the terminals when applying torque http://airpax.sensata.com/ Grams 62.4 Torque (in-lbs ...
Page 19
... The tripping current (TC) for all of the protectors is “1” (in the range of 125% to 135% of ampere rating except for the 400Hz protectors which is “2” (more than 135% of ampere rating) The overload rating (OL) - designates whether the protector has been tested for general use or motor starting applications. http://airpax.sensata.com/ Rated Current (Amps) Minimum Poles UL/CSA — ...
Page 20
... V at the end of the part number. The V will of the part number. The unit will not be VDE Approved. be added to any part number formed entirely from shaded decisions. If non-shaded areas are selected, the unit will not be VDE approved, but other approvals still apply. http://airpax.sensata.com/ Screw Terminals 6 Single pole ...
Page 21
... Green Green Off Black Yellow Yellow Off Notes: A. Bezels of IAGBX, IUGBX, IEGBX, CUGBX, CEGBX are black. B. Consult factory for other marking options. http://airpax.sensata.com/ 6 Sixth Decision Optional Standard hardware. No designation required. -A Metric thread mounting inserts and terminals -B Barriers* 277V (50/60Hz only) (See note 3) ...
Page 22
... Only one auxiliary switch is normally supplied on two pole approvals still apply. units. Switch is located in the right-hand pole (viewed from terminal end) unless otherwise specified CCC Approved This approval requires the addition the end of the part number. The unit will not be VDE Approved. http://airpax.sensata.com 1REC4 - ...
Page 23
... Green Green Off Black Yellow Yellow Off Notes: A. Bezels of LEGBX are black. B. Consult factory for other marking options. http://airpax.sensata.com/ 6 Sixth Decision Optional Standard hardware. No designation required. -A Metric thread mounting inserts and terminals -G Handle guard, (available in ZX, BX and snap-in versions only) ...
Page 24
... This document is generated from the AIRPAX™ full-line catalog #2455005000 printed in USA, January 2011 BUSINeSS CeNTeRS Sensata Technologies 807 Woods Road Cambridge, MD 21613, UsA phone: +1 410-228-1500 Brands: Airpax™ Sensata Technologies Inc. 529 Pleasant Street Attleboro, MA 02703, UsA phone: +1 508-236-3287 Brands: Klixon™, sensata technologies™ ...