NC9Z-MA11 IDEC, NC9Z-MA11 Datasheet - Page 8
![PANEL MOUNTING BRACKET](/photos/21/78/217889/4667637_sml.jpg)
NC9Z-MA11
Manufacturer Part Number
NC9Z-MA11
Description
PANEL MOUNTING BRACKET
Manufacturer
IDEC
Datasheet
1.NC9Z-LK1.pdf
(12 pages)
Specifications of NC9Z-MA11
Accessory Type
Panel Mounting Bracket
For Use With
Magnetic Hydraulic Circuit Breakers (1-Pole) - NC1V Series
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
NC1V Circuit Protectors
Time Delay Curve and Ambient
Temperature
NC1V circuit protectors employ an electromagnetic tripping
system, where the rated current (trip current) is not affected
by ambient temperatures. But the time delay may vary with
the oil viscosity in the oil dash pot. Lower oil viscosity at
higher temperatures results in a shorter delay, whereas at
lower temperatures the delay will be longer.
Temperature Correction Curve
The time delay curves on the preceding page are measured
at 40°C. With reference to the following curves, time delays
can be corrected according to ambient temperature.
The time delay is based on an ambient temperature of
40°C. Time delays at other temperatures are corrected
according to the temperature correction curve. The time
delay of the instantaneous time delay curve (S) is not
affected by the ambient temperature.
W h e n o p e r a t i n g t e m p e r a t u r e
exceeds 40°C, derate the rated
current by multiplying the derating
factor shown on the right.
Impedance and Coil Resistance
• Series Trip (Current Trip)
Tolerance: ±25% (up to 20A),
• Relay Trip (Voltage Trip)
Tolerance: ±25%
8
Current
Rated
0.1A
0.3A
0.5A
10A
15A
20A
25A
30A
1A
2A
3A
5A
7A
Tripping Voltage
24-48V
±50% (25A and 30A)
Curve S
600
500
400
300
200
100
0.025
0.014
0.007
0.006
0.005
0.004
0.003
66.0
1.92
0.50
0.16
0.07
80
60
40
6.6
-20
For AC 50/60 Hz
Impedance (Ω)
-10
0
Curves A, M
Ambient Temperature (°C)
10
116.0
0.050
0.027
0.021
0.010
0.006
0.005
0.004
11.0
3.65
0.93
0.27
0.12
20
30
Resistance (Ω)
40
Curve S
For DC
0.050
0.015
0.011
0.005
0.005
0.004
0.004
0.003
43.0
0.86
0.25
0.11
100.0
Operating
50
4.1
Temp.
50°C
55°C
60°C
Resistance (Ω)
60
For DC
70
Curves A, M
Derating
Factor
106.0
0.045
0.025
0.020
0.009
0.005
0.005
0.004
10.0
3.40
0.90
0.25
0.11
0.9
0.8
0.7
at 25°C
at 25°C
Inertia Delay
Inertia delay is designed not to trip on a non-repeating
single pulse of 20 times the rated current (peak value) for a
duration of 8 ms. In addition, circuit protectors equipped
with inertia delay do not respond to high inrush currents
caused by transformer or lamp loads, but perform the
specified interruption on the subsequent overcurrents.
Inertia delay is available on AC circuits, and is not available
with the series trip curve S (instantaneous).
Voltage Drop Due to Coil Resistance or Impedance
The internal resistance or impedance of a circuit protector
tends to be larger for a smaller rated current. Therefore,
when circuit protectors of a small rated current are used,
voltage drop should be taken into consideration. Internal
resistance also varies with time delay curves, which should
also be considered during installation.
12000
10000
8000
6000
4000
2000
1
2
3
1. Percent of rated current
2. Sinusoidal or parabolic pulse
Pulse Width (ms)
4
Protector rated current
Pulse peak current
5
Pulse width (Duration)
6
7
Pulse peak current
×100
8
9
10