PH300S48-24 TDK Corporation, PH300S48-24 Datasheet - Page 46
![no-image](/images/manufacturer_photos/0/6/653/tdk_corporation_sml.jpg)
PH300S48-24
Manufacturer Part Number
PH300S48-24
Description
Power Supply, Power Rating 300 Watt, Output Current Rating 12.50 Ampere
Manufacturer
TDK Corporation
Datasheet
1.PH300S48-24.pdf
(58 pages)
Specifications of PH300S48-24
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PH300S48-24
Manufacturer:
LAMBDA
Quantity:
37
Company:
Part Number:
PH300S48-24
Manufacturer:
LAMBDA
Quantity:
134
Part Number:
PH300S48-24
Quantity:
60
PH
B-344
PH
1 Input Voltage Range
Input voltage ranges for PH300S, 600S series are as fol-
low.
Input voltage normally includes ripple voltage (Vrpl) as
shown as Figure1-1. The ripple voltage shall be less than
following values.
Peak of input voltage wave shall not be exceed above in-
put voltage range.
Output voltage would be fluctuated as dynamic line chang-
es.
The output ripple voltage may become bigger if the bottom
of input ripple voltage is below 220V for 280VDC input
model and below 40VDC for 48VDC input model.
●Basic Connection
Fuse
300S, 600S
C1
48VDC Input : 36 - 76VDC
280VDC Input : 200 - 400VDC
48VDC Input : 4Vp-p
280VDC Input : 20Vp-p
+
C2
L1
Figure1-1 Ripple Voltage
C3
(PH300S)
Baseplate
+Vin
−Vin
CNT
2. Explanations on Specifications
Time
TRM
IOG
+S
+V
−V
−S
CS
50mm
C4
below
Vrpl
C5
Input
Voltage
Range
+
Load
+
−
t
Input Fuse
No internal fuse is provided in the power module. To en-
sure the safety operation and to acquire safety standard
approvals, attach an external fuse. The external fuse must
be fast blow type and be attached to each module indi-
vidually.
Furthermore, attach the fuse at +Vin side if the ground is
-Vin side and at -Vin side if the ground is at +Vin side.
Use in-rush current limit circuit when the in-rush current
may make troubles.
C1:
Attach electrolytic capacitor(s) between +Vin and -Vin ter-
minals.
The capacitor shall be lower equivalence series resistance
(ESR). Especially under low ambient temperature, the
voltage of C1 becomes unstable due to ESR at line off.
Hence, be aware the output might be not normal line off.
Confirm the allowance of ripple current because ripple cur-
rent flows in the capacitor, and then choose the capacitor.
Recommended Capacitor Values
L1:
To reduce C1 ripple current and output spike noise volt-
age, attach a normal choke coil to each module.
Recommended Inductance Values
Recommended Current Ratings
Table1-1 Recommended Rating Current of Input Fuse
280VDC Input
48VDC Input
Fuse
48VDC Input : 470μF
280VDC Input : 22μF
48VDC Input : 3μH
280VDC Input : 15μH
PH300S48-* : 11A
PH300S280-* : 2A
PH600S280-* : 4A
C1
+
C2
L1
Figure1-2 Basic Connection
C3
・All specifications are subject to change without notice.
(PH600S)
Baseplate
300W
+Vin
−Vin
CNT
20A
5A
TRM
IOG
+S
+V
−V
−S
CS
C4
600W
10A
−
C5
+
Load
+
−