ADC-HZ12BGC Murata Power Solutions Inc, ADC-HZ12BGC Datasheet - Page 2

• Manufacturer Part Number: ADC-HZ12BGC
• Description: Analog To Digital Converter
• Manufacturer: Murata Power Solutions Inc

Functional Specifications
PARAMETERS
INPUTS
+15V Supply, Pin 28
–15V Supply, Pin 31
+5V Supply, Pin 16
Digital Inputs, Pins 14, 21
Analog Inputs, Pins 24, 25
Buffer Input, Pin 30
Lead Temperature (10 seconds)
(Typical at +25°C and ±15V and +5V supplies unless otherwise noted)
Analog Input Ranges
Input Impedance
10k (±10V)
Input Impedance with Buffer
Input Bias Current of Buffer
Start Conversion
Resolution
Nonlinearity
Differential Nonlinearity
Accuracy Error
Temperature Coefficient
Diff. Nonlinearity Tempco
No Missing Codes
Conversion Time
Buffer Settling Time (10V step)
Power Supply Rejection
Parallel Output Data
command.
V
V
Unipolar Coding
Bipolar Coding
Complementary two’s complement
Serial Output Data
Compl. binary or compl. offset binary coding.
End of Conversion (Status)
during reset and conversion and logic "0"
when conversion complete.
Clock Output
for ADC-HX and 1.5MHz for
ADC-HZ (pin 17 grounded).
Internal Reference
Reference Tempco
External Reference Current
Gain (before adjustment)
Zero, Unipolar (before adj.)
Offset, Bipolar (before adj.)
Gain
Zero, Unipolar
Offset, Bipolar
12 Bits
10 Bits
8 Bits
Unipolar
Bipolar
5k (0 to +10V, ±5V)
OUT
OUT
("0") +0.4V
("1") +2.4V
ABSOLUTE MAXIMUM RATINGS
OUTPUTS
PERFORMANCE
ADC-HX12B
0 to +5V, 0 to +10V
±2.5V, ±5V, ±10V
2.5k (0 to +5V, ±2.5V)
50 megohms
125nA typical, 250nA max.
+2V min. to +5.5V max. positive pulse with dur-
ation of 100ns min. Rise and fall times <30ns.
Logic "1" to "0" transition resets converter and
initiates next conversion. Loading: 2 TTL loads.
12 bits
±1/2LSB max.
±3/4LSB max.
±0.2%
±0.1% of FSR
±0.2% of FSR
±20ppm/°C max.
±5ppm/°C of FSR max.
±10ppm/°C of FSR max.
±2ppm/°C of FSR max.
Over opererating temperature range
20μs max.
15μs max.
10μs max.
3μs to ±0.01%
±0.004%/% supply max.
12 parallel lines of data held until next conversion
Complementary binary
Complementary offset binary
NRZ successive decision pulses out, MSB first.
Conversion status signal. Output is logic "1"
Train of positive going +5V 100ns pulses. 600kHz
+6.3V
±20ppm/°C max.
2.5mA max.
LIMITS
±5.5
+18
–18
±25
±15
300
+7
www.murata-ps.com
ADC-HZ12B
8μs max.
6μs max.
4μs max.
UNITS
Volts
Volts
Volts
Volts
Volts
Volts
°C
PHYSICAL/ENVIRONMENTAL
Footnotes:
TECHNICAL NOTES
1.
2.
3.
4.
5.
6.
7.
12-Bit, 8 and 20μsec Analog-to-Digital Converters
Power Supply Voltages
–15V ±0.5V at –25mA
+5V ±0.25V at +85mA
Operating Temp. Range, Case
Storage Temperature Range
Package Type
Weight
Thermal Impedance
JC
JA
Adjustable to zero.
FSR is full scale range and is 10V for 0 to +10V or ±5V inputs and 20V for
±10V input, etc.
Without buffer amplifier used. ADC-HZ may require external adjustment
of clock rate.
Short cycled operation.
All digital outputs can drive 2 TTL loads.
It is recommended that the ±15V power input pins both be bypassed to ground with a 0.01μF ceramic
capacitor in parallel with a 1μF electrolytic capacitor and the +5V power input pin be bypassed to ground
with a 10μF electrolytic capacitor as shown in the connection diagrams. In addition, GAIN ADJUST (pin 27)
should be bypassed to ground with a 0.01μF ceramic capacitor. These precautions will assure noise free
operation of the converter.
DIGITAL COMMON (pin 15) and ANALOG COMMON (pin 26) are not connected together internally, and
therefore must be connected as directly as possible externally. It is recommended that a ground plane be
run underneath the case between the two commons. Analog ground and ±15V power ground should be
run to pin 26 whereas digital ground and +5V ground should be run to pin 15.
External adjustment of zero or offset and gain are made by using trimming potentiometers connected as
shown in the connection diagrams. The potentiometer values can be between 10k and 100k Ohms and
should be 100ppm/°C cermet types. The trimming pots should be located as close as possible to the con-
verter to avoid noise pickup. In some cases, for example 8-bit short-cycled operation, external adjustment
may not be necessary.
Short-cycled operation results in shorter conversion times when the conversion is truncated to less than
12 bits. This is done by connecting SHORT CYCLE (pin 14) to the output bit following the last bit desired.
For example, for an 8-bit conversion, pin 14 is connected to the bit 9 output. Maximum conversion times
are given for short-cycled conversions of 8 or 10 bits. In these two cases, the clock rate is accelerated by
connecting the CLOCK RATE adjust (pin 17) to +5V (10 bits) or +15V (8 bits). The clock rate should not be
arbitrarily speeded up to exceed the maximum conversion rate at a given resolution, as missing codes will
result.
Note that output coding is complementary coding. For unipolar operation it is complementary binary, and
for bipolar operation it is complementary offset binary or complementary two’s complement. In cases in
which bipolar coding of offset binary or two’s complement is required, this can be achieved by inverting the
analog input to the converter (using an op amp connected for gain of –1). The converter is then calibrated
so that –FS analog input gives an output code of 0000 0000 0000, and +FS – 1LSB gives 1111 1111 1111.
These converters can be operated with an external clock. To accomplish this, a negative pulse train is
applied to START CONVERT (pin 21). The rate of the external clock must be lower than the rate of the
internal clock as adjusted (see Short Cycle Operation tables) for the converter resolution selected. The
pulse width of the external clock should be between 100 and 300 nanoseconds. Each N-bit conversion
cycle requires a pulse train of N + 1 clock pulses for completion, e.g., an 8-bit conversion requires 9 clock
pulses for completion. A continuous pulse train may be used for consecutive conversions, resulting in an
N-bit conversion every N + 1 pulses, or the E.O.C. output may be used to gate a continuous pulse train for
single conversions.
When the input buffer amplifier is used, a delay equal to its settling time must be allowed between the input
level change, such as a multiplexer channel change, and the negative-going edge of the START CONVERT
pulse. If the buffer is not required, BUFFER INPUT (pin 30) should be tied to ANALOG COMMON (pin 26). This
prevents the unused amplifier from introducing noise into the converter. For applications not using the buffer,
the converter must be driven from a source with an extremely low output impedance.
ADC-HX, ADC-HZ Series
Technical enquiries email: [e-mail], tel:
POWER REQUIREMENTS
+15V ±0.5V at +20mA
0 to +70°C or –55 to +125°C
–65 to +150°C
32-pin ceramic TDIP
0.5 ounces (14 grams)
6°C/W
30°C/W
MDA_ADCHXHZ.B01 Page 2 of 6
[phone]