47747-000LF FCI, 47747-000LF Datasheet
47747-000LF
Specifications of 47747-000LF
Related parts for 47747-000LF
47747-000LF Summary of contents
Page 1
... GS-22-008. The part numbers that do not end in “LF” meet all regulations except for Pb in SnPb plating, if available. Tin plated “LF” product has 100% tin plating in the interface and has not been tested for whisker growth in all interconnect environments. Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION ...
Page 2
... ASTM B-194: Copper-Beryllium Alloy Plate, Sheet, Strip and Rolled Bar 4.4.5 ANSI/ASQC M-1: American National Standard for Calibration Systems 4.4.6 BUS-03-404: FCI Test Specification for Normal Force Measurements 4.4.7 BUS-03-302: FCI Test Specification for Sulfide Vapor Test 4.4.8 TA-75: FCI Latch Housing Mini-PV Crimp/Application Data 5 ...
Page 3
... As an option, in some cases one or more housing positions can be molded closed. In either case, the polarized position is rendered non-functional. Special external polarization, keying and/or latching features are available depending on part number and specific requirements. Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K ...
Page 4
... MIL-STD-202,Method 302. The following details shall apply: a. Test Voltage - 500 volts DC b. Electrification Time - 2 minutes c. Points of Measurement - Between adjacent and opposing contacts. Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K STATUS: NUMBER ...
Page 5
... TYPE TITLE Crimp-to Wire, Mini-PV™ Receptacles and Mini-Latch Housings Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K STATUS: NUMBER BUS-12-067 PAGE REVISION AUTHORIZED BY DATE H.T. Brewbaker 31-May-06 CLASSIFICATION UNRESTRICTED GS-01-001 Released Printed: Jan 04, 2007 . ...
Page 6
... TYPE TITLE Crimp-to Wire, Mini-PV™ Receptacles and Mini-Latch Housings Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K STATUS: NUMBER BUS-12-067 PAGE REVISION AUTHORIZED BY DATE H.T. Brewbaker 31-May-06 CLASSIFICATION UNRESTRICTED GS-01-001 Released Printed: Jan 04, 2007 . ...
Page 7
... Normal Force - The minimum contact normal forces shall be as shown in Table I when tested in accordance with FCI Test Specification BUS-03-404, by the Probe Method ( par 3. deflection equivalent to a 0.024" gauge pin. This requirement must be met before and after environmental testing ...
Page 8
... TYPE TITLE Crimp-to Wire, Mini-PV™ Receptacles and Mini-Latch Housings Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K STATUS: NUMBER BUS-12-067 PAGE REVISION AUTHORIZED BY DATE H.T. Brewbaker 31-May-06 CLASSIFICATION UNRESTRICTED GS-01-001 Released Printed: Jan 04, 2007 . ...
Page 9
... TYPE TITLE Crimp-to Wire, Mini-PV™ Receptacles and Mini-Latch Housings Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K STATUS: NUMBER BUS-12-067 PAGE REVISION AUTHORIZED BY DATE H.T. Brewbaker 31-May-06 CLASSIFICATION UNRESTRICTED GS-01-001 Released Printed: Jan 04, 2007 . ...
Page 10
... Table IV when tested in accordance with MIL- STD-1344, Method 2003 cross-head parting speed of one inch per minute maximum. Wire Size, AWG Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION TABLE II - MATING FORCES Spring Thickness (Mils) Force (Grams) 3.5 4.8 5 ...
Page 11
... Vibration - MIL-STD-1344, Method 2005, Test Condition III, Mated. During vibration along each axis, the contacts shall evidence no discontinuity greater than one microsecond. Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K STATUS: ...
Page 12
... Connector - Ten (10) of the largest and seven (7) of the smallest population connectors shall be subjected to the qualification inspection. A separate group of seventeen (17) connectors shall be subjected to test for each combination of retention spring thickness, contact area plating, and housing contact spacing. Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K ...
Page 13
... Except all contacts used for total mating force. *NOTE: Except use a total of 30 contacts for individuals contact insertion/withdrawal forces. 9.4.3 Stranded Wire - All stranded wire used in these qualification test samples shall conform to the requirements of MIL-W-16878, Type B. Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION TABLE V - CONTACT SAMPLES ...
Page 14
... A significant change is made to the manufacturing process which impacts the product form, fit or function significant event occurs during production or end use requiring corrective action to be taken relative to the product design or manufacturing process. Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K STATUS: ...
Page 15
... TYPE TITLE Crimp-to Wire, Mini-PV™ Receptacles and Mini-Latch Housings Copyright FCI Form E-3334 Rev E PRODUCT SPECIFICATION PDM: Rev:K STATUS: NUMBER BUS-12-067 PAGE REVISION AUTHORIZED BY DATE H.T. Brewbaker 31-May-06 CLASSIFICATION UNRESTRICTED GS-01-001 Released Printed: Jan 04, 2007 . ...
Page 16
... F 8 Add DIM. “D” to Figure 5 and change guardian G All Revised format to be consistent with GS-01-001, and change BERG, Dupont, etc. references to FCI 5.2.3 Changed V-1 or better to V-0 5.2.4 Changed V-1 or better to V Add sections 3.1 and 3.2, add LF information to section section 5 ...