PS1000-R06L SMC Corporation of America, PS1000-R06L Datasheet - Page 4
![STEM](/photos/21/47/214715/363878906-40_sml.jpg)
PS1000-R06L
Manufacturer Part Number
PS1000-R06L
Description
STEM
Manufacturer
SMC Corporation of America
Series
PS1000r
Specifications of PS1000-R06L
Connection Size
6mm
Operating Pressure Range
-0.1MPa To 0.45MPa
Operating Temperature Range
0°C To +60°C
Svhc
Bis (2-ethyl(hexyl)phthalate) (DEHP) (15-Dec-2010)
External Depth
30mm
External Length /
RoHS Compliant
Accessory Type
*
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
*
1. Confirm the specifications.
1. Instruction manual
2. Securing the space for maintenance
3. Tightening torque
1. Before piping
2. Wrapping of pipe tape
1. Operating fluid
2. Install an air dryer, aftercooler, etc.
3. Drain flushing
16-14-4
Products represented in this catalog are designed for use in
compressed air appllications only (including vacuum), unless
otherwise indicated.
Do not use the product outside their design parameters.
Please contact SMC when using the products in applications
other than compressed air (including vacuum).
Install the products and operate them only after reading the
instruction manual carefully and understanding its contents.
Also keep the manual where it can be referred to as
necessary.
When installing the products, please allow access for
maintenance.
When installing the products, please follow the listed torque
specifications.
Make sure that all debris, cutting oil, dust, etc, are removed
from the piping.
When screwing piping or fittings into ports, ensure that chips
from the pipe threads or sealing material do not get inside the
piping. Also, when the pipe tape is used, leave 1.5 to 2 thread
ridges exposed at the end of the threads.
Please consult with SMC when using the product in
applications other than compressed air (including vacuum).
Regarding products for general fluid, please ask SMC about
applicable fluids.
Excessive condensate in a compressed air system may cause
valves and other pneumatic equipment to malfunction.
Installation of an air dryer, after cooler etc. is recommended.
If condensate in the drain bowl is not emptied on a regular
basis, the bowl will over flow and allow the condensate to
enter the compressed air lines.
If the drain bowl is difficult to check and remove, it is
recommended that a drain bowl with the auto-drain option be
installed.
For compressed air quality, refer to “Air Preparation
Equipment” catalog.
Warning
Warning
Caution
Warning
Common Precautions
Be sure to read before handling.
For detailed precautions on every series, refer to main text.
Air Supply
Selection
Mounting
Piping
4. Use clean air
1. Do not use in environments where the product
2. Do not expose the product to direct sunlight
3. Do not use in a place subject to heavy
4. Do not mount the product in locations where it
1. Maintenance procedures are outlined in the
2. Maintenance work
3. Drain flushing
4. Shut-down before maintenance
5. Start-up after maintenance and inspection
6. Do not make any modifications to be product.
If the compressed air supply is contaminated with chemicals,
cynthetic materials, corrosive gas, etc., it may lead to break
down or malfunction.
is directly exposed to corrosive gases,
chemicals, salt water, water or steam.
for an extended period of time.
vibrations and/or shocks.
is exposed to radiant heat.
operation manual.
Not following proper procedures could cause the product to
malfunction and could lead to damage to the equipment or
machine.
If handled improperly, compressed air can be dangerous.
Assembly, handling and repair of pneumatic systems should
be performed by qualified personnel only.
Remove drainage from air filters regularly. (Refer to the
specifications.)
Before attempting any kind of maintenance make sure the
supply pressure is shut of and all residual air pressure is
released from the system to be worked on.
Apply operating pressure and power to the equipment and
check for proper operation and possible air leaks. If operation
is abnormal, please verify product set-up parameters.
Do not take the product apart.
Warning
Warning
Operating Environment
Maintenance