INFRESCO P 6KW UNITED AUTOMATION, INFRESCO P 6KW Datasheet

INFRESCO P 6KW

Manufacturer Part Number

INFRESCO P 6KW

Description

INFRESCO, PIR 6KW

Manufacturer

UNITED AUTOMATION

Datasheet

1.INFRESCO_P_6KW.pdf (4 pages)

Specifications of INFRESCO P 6KW

Operating Temperature Max

40Â°C

Operating Temperature Min

-20Â°C

Approval Bodies

External Depth

75mm

External Length / Height

130mm

Ip/nema Rating

Load Power

For Use With

Quartz Infrared Halogen Lamps

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 4
Download datasheet (179Kb)

Typical applications are Pub Patio areas, Smoking Shelters, Restaurants, Warehouses,

Work shops. Garden Lighting

PRODUCT FEATURES & BENEFITS

Significant energy saving - provides heat only when people are present

INTRODUCTION

The infresco-P 6kW is part of a family of controllers designed to provide energy saving

when used with Quartz Infrared Halogen Lamps or other Heating Lighting Products.

The ‘P’ model has a built in PIR sensor allowing the lamps to automatically switch on

only when people are present. In addition to the PIR, a temperature sensor monitors the

outside temperature and inhibits the lamps when the temperature exceeds a pre-

determined set point of between 5 and 25 degrees Celsius. Designed with ease of

wiring in mind, this unit is ideal for controlling up to four 1.5kW lamps through the use of

two additional cable entry points.

The microcontroller-based unit incorporates zero-voltage switching and a soft-start

function to eliminate the lamps’ initial high inrush current – potentially increasing lamp

life by as much as 30% and reducing the stress on the mains supply.

The lamps are switched on for a pre-determined time period of between 5 and 30

minutes. This period is reset each time the PIR detects any further movement.

Installation is simple and once installed is relatively maintenance free.

Extends lamp Life

Temperature monitor – lamps inhibited when ambient temperature exceeds set point

Ideal for controlling up to 4 x 1.5kW lamps

Soft-start/zero-voltage switch-off

Low-cost

Easy to install

INSTALLATION

Important: Read carefully the following information before installing the unit.

The passive infrared sensor (PIR) fitted in this unit detects changes of infrared energy

through the Fresnel lens on the front face of the unit. The detection area and range

depend significantly on its mounting position. The PIR not only detects movement of the

human body, but also other heat sources similar to the human body.

To prevent false activation, the unit must not be located directly facing or in close

proximity to the heater lamps. Avoid locating the unit near to heating flues/exhausts, air

conditioning units, moving trees/bushes and reflective surfaces.

To prevent malfunction of the PIR sensor, avoid subjecting it to rapidly-changing

temperatures, strong shock or vibration or high humidity and temperature.

WIRING

Warning! Ensure the mains supply has been isolated before wiring this unit.

Failure to do so could result in serious injury or fatality.

The unit is fitted with three cable glands. Only one cable should be fitted per gland to

maintain the unit’s IP rating. Two additional cable glands can be fitted to allow the

connection of up to four lamps. See Figure 2.

The mains supply connects to the terminal block marked ‘LINE’. Connect the supply

LIVE to the ‘L’ terminal, NEUTRAL to the ‘N’ terminal and EARTH to the ‘E’ terminal.

The lamps connect to the terminal block marked ‘LOAD’. Connect the load LIVE to the

‘L’ terminal, NEUTRAL to the ‘N’ terminal and EARTH to the ‘E’ terminal. The load

connections are paired to allow the connection of several lamps.

Important: Ensure all earth wires are connected to maintain earth continuity to

the lamp fittings.

If the ‘Enable’ input is not being used, make sure a link is fitted between the ‘COM’ and

‘INPUT’ terminals (CN3).

Connect the 3-way plug to the socket marked ‘PIR SENSOR’ (CN4).

Check all wiring - particularly the Line, Earth and Load connections and make sure the

cable glands are tightened.

It is recommended that installation and maintenance of this equipment should be done

with reference to the current edition of the I.E.E. wiring regulations (BS7671) by

suitably qualified/trained personnel.

These regulations contain important requirements regarding safety of electrical

equipment (for International Standards refer to I.E.C/ directive IEC950).

WARNING: THIS UNIT MUST BE EARTHED

Related parts for INFRESCO P 6KW

INFRESCO P 6KW Summary of contents

Page 1

INTRODUCTION The infresco-P 6kW is part of a family of controllers designed to provide energy saving when used with Quartz Infrared Halogen Lamps or other Heating Lighting Products. The ‘P’ model has a built in PIR sensor allowing the lamps ...

Page 2

... C IP Rating 65 Gland Diameter (Fitted) Max Cable Entry 2.5mm² 4 Lamp Installation Must be fitted in Parallel UNITED AUTOMATION LIMITED 1 Southport Business Park Tel: 0044 (0) 1704 – 516500 Main Kew Tel: 0044 (0) 1704 - 516516 Sales Southport, PR8 4HQ Fax: 0044 (0) 1704 – 516501 ENGLAND Enquiry@united-automation ...

Page 3

PIR DETECTION ZONE POSITIONING The Infresco-P 6kW can be wall or ceiling-mounted. For wall-mounting, the unit should be positioned 2-3 metres high with the cable glands facing down. Refer to the PIR detection patterns shown in Figure 1 when deciding ...

Page 4

WIRING OPTION 1 WIRING OPTION 2 DIMENSIONS Commissioning Turn the lamp on-time preset (VR2) fully anti-clockwise to select ‘walk test’ mode. Check the PIR sensitivity preset (VR3) is set to approximately the half-way position (factory default). The temperature set point ...

Related keywords

INFRESCO P 6KW datasheet
INFRESCO P 6KW data sheet
INFRESCO P 6KW pdf datasheet
INFRESCO P 6KW component
INFRESCO P 6KW part
INFRESCO P 6KW distributor
INFRESCO P 6KW RoHS
INFRESCO P 6KW datasheet download