ETM1411-2307 CAL CONTROLS, ETM1411-2307 Datasheet

ETM1411-2307

Manufacturer Part Number

ETM1411-2307

Description

DIGITAL TIMER, 1 X RELAY, 230VAC

Manufacturer

CAL CONTROLS

Datasheet

1.ETM1411-2307.pdf (2 pages)

Specifications of ETM1411-2307

Supply Voltage Range

184VAC To 253VAC

Operating Time Range

Selectable 0.01 To 99.59 Min Or Hour

Power Consumption

3VA

External Depth

70mm

External Length / Height

34mm

External Width

77mm

Ip/nema Rating

IP60 Front Panel / IP20 Rear Panel

Rohs Compliant

Yes

Digit Height

12mm

Input Voltage Max

230VAC

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (113Kb)

SUPPLY:

184-253V AC

50/60Hz 3VA

NOTE :

Connection Diagram

SN: XXXXXXXXX

Thank you for choosing the CAL ETM1411 digital timer.

* 34 x 77mm sized.

0:01 .... 99:59 min.

0:01 .... 99:59 hour

ETM1411-230VAC

DIGITAL TIMER

Single contact output for timing control.

External start input.

Display can be adjusted to show min. or sec.

Scale ;

Decrease and increace step of time can be adjusted.

Start and stop possibility by front panel.

16 different warning tones.

Upper and lower limits of the setpoint can be adjusted.

CE marked according to European Norms.

Output

Relay

CAL ETM1411 DIGITAL TIMER

www.cal-controls.com

12V AC/DC %10

24V AC/DC %10

Supply Voltage

230V AC +%10 -%20

CAL ETM 411 is intended for installation in control panels. Make sure that the device is

used only for intended purpose. The shielding must be grounded on the instrument side.

During an installation, all of the cables that are connected to the device must be free of

electrical power. The device must be protected against inadmissible humidity, vibrations,

severe soiling and make sure that the operation temperature is not exceeded. All input and

output lines that are not connected to the supply network must be laid out as shielded and

twisted cables. These cables should not be close to the power cables or components. The

installation and electrical connections must be carried out by qualified staff and must be

according to the relevant locally applicable regulations.

Neutral

Line

Fuse should

be connected.

F 100 mA

250V AC

Fuse

START

Switch

Cable size: 1,5mm²

SN: XXXXXXXXX

ETM1411-230VAC

ETM1411-12

ETM1411-24

Order Code

ETM1411-12

DIGITAL TIMER

www.cal-controls.com

230V AC

Supply

IEC 60227 or IEC 60245.

supply switch shall bring the identification of

the relevant instrument and it should be easily accessible

by the operator.

Note:

Mains supply cords shall meet the requirements of

In accordance with the safety regulations, the power

9 10 11 12

START

ETM1411

CAL

OUT

DIGITAL TIMER

Holding screw

0.4-0.5Nm

HOUR

Equipment is protected throughout

by DOUBLE INSULATION.

MIN

SET

START

STOP

1/2

Dimensions

CAL CONTROLS LTD

Bury Mead Road, Hitchin, Herts, SG5 1RT, UK.

Tel : +44 (0) 1462 436161

e-mail: sales@cal-controls.co.uk

TECHNICAL SPECIFICATIONS

On and Off times for input pulses

ENVIRONMENTAL CONDITIONS

Ambient/storage temperature

Supply

Power consumption

Wiring

Scale

Sensitivity

Time Accuracy

Indicator

EMC

Safety requirements

OUTPUT

OUT

Life expectancy for relay

START INPUT

Input type

HOUSING

Housing type

Dimensions

Weight

Enclosure material

Max. Relative humidity

Rated pollution degree

Height

ELECTRICAL CHARACTERISTICS

ETM1411

CAL

OUT

Do not use the device in locations subject to corrosive and flammable gases.

While cleaning the device, solvents (thinner, benzine, acid etc.) or

START

DIGITAL TIMER

HOUR

85mm

MIN

ETM1411-230VAC

TIMER

Fax : +44 (0) 1462 451801

XXXXXXXXX

2.5mm² screw-terminal connections

EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B is satisfied for EMC tests.

The device is designed to operate in controlled electromagnetic environment)

EN 61010-1: 2001 (

Relay: 250V AC, 8A (

Suitable for panel mounting

W77xH34xD70mm

Approx. 240g (after packing)

Self extinguishing plastics

230V AC +%10 -%20, 50/60Hz or 24V AC/DC %10, 50/60Hz or 12V AC/DC %10, 50/60Hz.

Max 3VA

Selectable 99:59 min. or hour.

1 sec.

±%1

4 digits, 12mm, 7 parts yellow LED

Mechanical 30.000.000 operation; Electrical 100.000 operation

SET

DIGITAL

0 ... +50°C/-25 ... +70°C (with no icing)

80% up to 31°C decreasing linearly 50% at 40°C.

According to EN 60529

Max.

Web : www.cal-controls.com

START

SN:

STOP

Control with mechanical contact.

Min. = 100ms, Max. =

2000m

pollution degree 2, overvoltage category II

mounting

For removing mounting clamps:

for resistive load

clamp

Push out the mounting clamp

in direction

in the figure below. Then, pull

out the clamp in direction

Panel cut-out

as shown

Front panel :

Rear panel :

), NO+NC

71mm

corrosive materials

mounting

Ip20

clamp

IP60

Note: 1) Panel thickness

)

2) If there is no 60mm

Depth

should be maximum

7 mm.

free space at the back

side of the device, it

would be difficult to

remove it from the panel.

70mm

must not be used.

Panel

ETM1411-E-03

Rubber

gasket

8mm

Related parts for ETM1411-2307

ETM1411-2307 Summary of contents

Page 1

... CAL ETM1411 DIGITAL TIMER Thank you for choosing the CAL ETM1411 digital timer 77mm sized. * Single contact output for timing control. * External start input. * Display can be adjusted to show min. or sec. * Scale ; 0:01 .... 99:59 min. 0:01 .... 99:59 hour * Decrease and increace step of time can be adjusted. ...

Page 2

... Stop key Indicator Power Out TYP.1 Start input Indicator CONTROL DIAGRAM BY START & STOP KEYS Out.t. TYP.0 Str.t. Power Out Start TYP.2 key Stop key Indicator Power Out Start TYP.3 key Stop key Indicator key, the value can be TYP.1 TYP.1 ETM1411-E-03 ...

Related keywords

ETM1411-2307 datasheet
ETM1411-2307 data sheet
ETM1411-2307 pdf datasheet
ETM1411-2307 component
ETM1411-2307 part
ETM1411-2307 distributor
ETM1411-2307 RoHS
ETM1411-2307 datasheet download