61FD21T 100-240AC Omron, 61FD21T 100-240AC Datasheet - Page 6

• Manufacturer Part Number: 61FD21T 100-240AC
• Description: CONDUCTIVE LEVEL CONTROLLER, 230V
• Manufacturer: Omron

Specifications of 61FD21T 100-240AC

• Supply Voltage: 230VAC
• Response Time: 10s
• Power Consumption: 5VA
• Svhc: No SVHC (15-Dec-2010)
• Approval Bodies: CE
• Contact Configuration: Self-hold
• Contact Current Max: 6A

Safety Precautions
Definition of Precaution Information
Precautionary Information
Do not touch the terminals while power is being supplied.
Doing so may possibly result in electric shock.
■ Precautions for Safe Use
• Do not disassemble, repair, or modify the product.
• When attaching the product to the DIN rail, attach it firmly with
• When attaching the product to the DIN rail, ensure that the product
• If the thickness of a mounting panel is not adequate, or a mistake
• Ensure that terminal screws have been tightened firmly.
• When using the product, ensure that the wiring is correct before
• Use a power-supply voltage that is within the range of
• Use the control source and power supply or power lines that
• Do not install near heat-generating devices (coils, or devices that
• Be sure to confirm terminal numbers for correct wiring.
• Ensure that wiring is correct. Double-check materials such as
• Properly ground the grounding terminal. Ensure that the common
• If electrodes make contact with liquid, purchase and use a
• Keep appropriate distance from devices that generate high-
• Do not turn a setting volume beyond the scope of movement.
• Do not connect anything to unused terminals.
• Use SELV power supply with over load protection function for DC
screws.
has been attached firmly.
has been made during installation, the product may become
disconnected.
Recommended torque: 0.49 N·m
Assured torque: 0.59 N·m
turning on the power.
specifications.
provide inputs with appropriate specifications.
use coils).
connection charts and circuit diagrams.
electrode terminal has been properly grounded. Doing so can
alleviate effects from noise.
separator to prevent such contact.
frequency noise (e.g., high-frequency welders, electronic sewing
machines).
power supply. The insulation of SELV power supply must be a
double or reinforced between input and output. The output voltage
shall be 30 Vr.m.s. and 42.4 V at peak, or use the power supply of
60 V DC max. Recommended power supply: type S8VS-06024@
(OMRON made)
!CAUTION
!Caution
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury or in property damage.
In the interest of product improvement, specifications are subject to change without notice.
Do not keep, install, or use this product
in the following environments.
• Outdoors, or places subject to direct sunlight or wearing weather.
• Places where temperature and humidity exceed the allowable
• Places where there are extreme changes in temperature and
• Places subject to static electricity or inductive noise.
• Places subject to electrical fields.
• Places where vibrations or physical shocks are strong.
• Places where flammable gasses or flammable liquids exist.
• Places where corrosive gases (in particular, sulfuric or ammonia
• Places with large amounts of dust or iron powders.
• Places where water or oil come in contact with the product.
• Places subject to salt-water splashes.
■ Precautions for Correct Use
For Proper Use
1. Make sure to use setting values appropriate for the controlled
2. When discarding, properly dispose of the product as industrial
3. Only use this product within a board whose structure allows no
4. To avoid damage to the exterior of the product, do not use organic
About Installation
1. When wiring, use only recommended crimp terminals.
2. Do not block areas around the product for proper dissipation of
Noise Countermeasures
1. Do not install the product near devices generating strong high
2. When using a noise filter, check the voltage and current and
3. In order to prevent inductive noise, wire the lines connected to the
To avoid faulty operations,
malfunctions, or failure, observe the
following operating instructions.
1. During insulation resistance measurements, never apply the
2. Use a power supply that will reach rated voltage within 1 second.
range of the product specifications.
humidity, or icing or condensation may occur.
gas) exist.
object. Failure to do so can cause unintended operation, and may
result in accident or corruption of the product.
waste.
possibility for fire to escape.
solvents (thinner, benzene) or agents with strong alkalinity or
acidity.
heat. (If you do not secure space for heat dissipation, life cycle of
the product will be compromised.)
frequency waves or surges.
install it as close to the product as possible.
product separately from power lines carrying high voltages or
currents. Do not wire in parallel with or on the same cable as
power lines. Other measures for reducing noise include running
lines along separate ducts and using shield lines.
megohmmeter across the electrode terminals.
61F-D21T-V1
6