1-6605718-1 Tyco Electronics, 1-6605718-1 Datasheet

1-6605718-1

Manufacturer Part Number

1-6605718-1

Description

CONN MAG45 MOD JACK GRN/GRN PCB

Manufacturer

Tyco Electronics

Series

Mag45™r

Datasheet

1.1-6605718-1.pdf (7 pages)

Specifications of 1-6605718-1

Connector Type

RJ45

Number Of Ports

Number Of Rows

Mounting Type

Panel Mount; Through Hole, Right Angle

Speed

10/100 Base-T

Height Above Board

0.545" (13.84mm)

Led Color

Green - Green

Number Of Cores Per Jack

Shielding

Shielded

Tab Direction

Features

Board Guide

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 7
Download datasheet (38Kb)

1.1.

1.2.

1.3.

2.1.

2.2.

3.1.

Harrisburg, PA

All International Rights Reserved.

SCOPE

Content

This specification covers performance, tests and quality requirements for the Tyco Electronics Mag45*

Modular Jacks with Integrated Magnetics.

Qualification

When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.

All inspections shall be performed using the applicable inspection plan and product drawing.

Qualification Test Results

Successful qualification testing on the subject product line was completed on 20Jun00. The

Qualification Test Report number for this testing is 501-524. This documentation is on file at and

available from Engineering Practices and Standards (EPS).

APPLICABLE DOCUMENTS

The following documents form a part of this specification to the extent specified herein. Unless

otherwise specified, the latest edition of the document applies. In the event of conflict between the

requirements of this specification and the product drawing, the product drawing shall take precedence.

In the event of conflict between the requirements of this specification and the referenced documents,

this specification shall take precedence.

Tyco Electronics Documents

Industry Standards

REQUIREMENTS

Design and Construction

Product shall be of the design, construction and physical dimensions specified on the applicable

product drawing.

109-197:

501-524:

502-1129:

ANSI X3.263:

EIA-364:

FCC Part 68:

IEEE 802-3:

MIL-STD-202: Test Method Standard - Electronic and Electrical Component Parts

MIL-STD-810: Test Method Standard - Environmental Engineering Considerations and

Product

Specification

Mag45* Modular Jacks With Integrated Magnetics

* Trademark

| Indicates change

AMP Test Specifications vs EIA and IEC Test Methods

Qualification Test Report

Engineering Report

Information Technology - Fibre Distributed Data Interface (FDDI) - Token Ring

Twisted Pair Physical Layer Medium Dependent (TP-PMD)

Electrical Connector/Socket Test Procedures Including Environmental

Classifications

Connection of Terminal Equipment to the Telephone, Connector Specifications

Local Area Networks: Carrier Sense Multiple Access With Collision Detection

(CSMA/CD) Access Method and Physical Layer Specification

Laboratory Tests

For latest revision, visit our website at www.tycoelectronics.com\documents.

For Regional Customer Service, visit our website at www.tycoelectronics.com

108-2100

15Aug05 Rev B

1 of 7

LOC B

Related parts for 1-6605718-1

1-6605718-1 Summary of contents

Page 1

... This specification covers performance, tests and quality requirements for the Tyco Electronics Mag45* Modular Jacks with Integrated Magnetics. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 1.3. Qualification Test Results Successful qualification testing on the subject product line was completed on 20Jun00 ...

Page 2

... Product Codes for this product family are H363, H364, H365 and H366 3.5. Performance and Test Description Product is designed to meet the electrical, mechanical and environmental performance requirements specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental conditions per EIA-364. 3.6. Test Requirements and Procedures Summary Test Description Examination of product ...

Page 3

... Measure force necessary to mate specimens at a maximum rate of 12.7 mm [.5 in] per minute. EIA-364-13B. Measure force necessary to unmate specimens at a maximum rate of 12.7 mm [.5 in] per minute. EIA-364-4. Measure and record normal force generated at any given deflection level within the normal operating range with an FCC compliant modular plug ...

Page 4

... Class IIA for 10 days. Subject mated and mounted specimens to 2 hours at each of the following temperatures: -5, 25, 55 and 75 ± MIL-STD-810, Method 507.3. Subject mated and mounted specimens to 10 cycles (10 days) between 30 and ± RH. EIA-364-26, Test Condition B. Subject specimens to 5% spray for 48 hours. / ...

Page 5

... Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test group 1 shall consist of 16 specimens. Test groups 2 and 3 shall each consist of 1 specimen. Test group 4 shall consist of 45 specimens. B. Test Sequence Qualification inspection shall be verified by testing specimens as specified in Figure 2. ...

Page 6

... Acceptance Acceptance is based on verification that the product meets the requirements of Figure 1. Failures attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to confirm corrective action is required before resubmittal ...

Page 7

... Rev B 108-2100 ...

Related keywords

1-6605718-1 datasheet
1-6605718-1 data sheet
1-6605718-1 pdf datasheet
1-6605718-1 component
1-6605718-1 part
1-6605718-1 distributor
1-6605718-1 RoHS
1-6605718-1 datasheet download