SNAP-PAC-R1 OPTO 22, SNAP-PAC-R1 Datasheet - Page 4
![Programmable Controller](/photos/21/48/214893/4333751_sml.jpg)
SNAP-PAC-R1
Manufacturer Part Number
SNAP-PAC-R1
Description
Programmable Controller
Manufacturer
OPTO 22
Type
PLCr
Specifications of SNAP-PAC-R1
Accessory Type
Programmable Automation Communication
Leaded Process Compatible
No
Peak Reflow Compatible (260 C)
No
Signal Input Type
Ethernet, RS-232
Brand/series
SNAP Series
Communication
RS-232
Current, Input
1.2 A
Dimensions
3.313"L×1.75"W×4.188"H
Input Type
Analog/Digital/Serial
Memory
32 MB (Total RAM), 2 MB (Battery-Backed RAM), 8 MB (Flash)
Mounting Type
Rack
Output Type
Analog/Digital/Serial
Primary Type
Controller
Voltage, Supply
5-5.2 VDC
For Use With
SNAP PAC System
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
PAGE
4
Specifications
Specifications are continued on the following page.
Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com
SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com
© 2007–2011 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
Processor
Memory
Removable storage
Backup battery
Communication (wired)
Communication (wireless)
I/O unit compatibility
Power requirements
Hold-down screw
Environmental
Software
Agency certifications
Warranty
Total RAM
Battery-backed RAM
Flash
Ethernet
RS-232 serial
Topologies
Security
Frequency 802.11a
Frequency 802.11b/g
Transmit Power
Antenna Connector
Roaming
Operating temperature
Storage temperature
Humidity
PAC Project Basic
PAC Project Professional
3
200 MHz 32-bit ColdFire
Wired+Wireless models 32 MB; other models 16 MB (All models: 4 MB available for
PAC Control strategy; 2 MB for file storage)
(Models manufactured November 2008 and later; requires firmware R8.4 or higher)
MicroSD card slot: supports MicroSD card up to 2 GB maximum
Rechargeable (recharges whenever the brain has power), 3-year power-off data
retention
Two independent 10/100 Mbps Ethernet network interfaces (RJ-45 connectors)
Each interface has a separate IP address. Connects to host and I/O.
One RS-232 serial port
and PPP) or serial device. Cannot connect to serial I/O.
Wireless LAN interface with separate IP address.
Infrastructure, Ad-Hoc
802.11i: AES - Compatible with WPA2 Personal, TKIP - Compatible with WPA Per-
sonal, WEP. Note: TKIP/AES security is not supported in Ad-Hoc mode.
5.180–5.240 GHz, 5.745–5.825 GHz
2.412–2.472 GHz, 2.484 GHz
15 dBm maximum
Reverse polarity SMA (RP-SMA or RSMA)
Supported within an SSID (Service Set Identifier) only
SNAP PAC I/O units: SNAP PAC R-series and EB-series I/O units
5.0
Torque: 8 in-lb (0.9 N-m)
0 °C to 60 °C
-40 °C to 85 °C
0% to 95% relative humidity, non-condensing
Includes programming, HMI software, and configuration software; included with pur-
chase of controller.
PAC Project Basic plus OPC 2.0-compliant OPC server, database connectivity,Opto-
Control strategy and OptoDisplay project importing, and support for Ethernet link
redundancy or network segmenting.
(-W models only) U.S., FCC Part 15 Subpart C; Canada, IC RSS-210
(-FM models only) Factory Mutual approved
30 months from date of manufacture
2 MB (1 MB available for PAC Control strategy)
8 MB (3.25 MB available for PAC Control strategy; 384 KB available for file storage)
–
5.2 VDC @ 1.5 A
1
2
®
with hardware handshaking. Connects to host (via modem
5475 with integrated floating-point unit (FPU)
SNAP PAC R-Series Controllers