ELC-EX16NNDT-1 EATON CUTLER HAMMER, ELC-EX16NNDT-1 Datasheet - Page 27
![Programmable Logic Controller](/photos/21/26/212677/4551006_sml.jpg)
ELC-EX16NNDT-1
Manufacturer Part Number
ELC-EX16NNDT-1
Description
Programmable Logic Controller
Manufacturer
EATON CUTLER HAMMER
Datasheet
1.ELC-EX06NNNI-2.pdf
(34 pages)
Specifications of ELC-EX16NNDT-1
Signal Input Type
DC
Output Type
Transistor
No. Of Inputs
8
No. Of Outputs
8
For Use With
Eaton ELC Controllers
February 2009
Product Description
The Cutler-Hammer Intelligent Tech-
nologies (IT.) EtherNet/IP (D77D-EIP)
from Eaton’s electrical business has
greatly increased the functionality of
Cutler-Hammer IT. communicating
products, allowing monitoring and
control for IT. motor control devices.
The adapter concentrates all data
from these devices into a single
EtherNet/IP node.
The EtherNet/IP Adapter is a slave
device on EtherNet/IP.
To simplify the configuration of the
D77D-EIP, a simple auto-configure
button press sets the system up for
default operation. This automatically
configures the EtherNet/IP assemblies
to the I/O system devices.
Application Description
In a typical EtherNet/IP Adapter appli-
cation, the D77D-EIP connects directly
to EtherNet/IP, and resides in a system
with communicating motor controls.
The data from these IT. devices is
assembled into input and output
assemblies before being presented
to EtherNet/IP.
CA08102001E
Cat. No. D77D-EIP
Features, Functions and Benefits
■
■
■
■
■
■
Standards and Certifications
Approvals
Table 50-38. Approvals/Certifications
Electrical/EMC
Other Approvals
Technical Data and Specifications
Table 50-39. Environmental Ratings
Transportation/Storage
Operating
Description
ESD Immunity (IEC 61000-4-2)
Radiated Immunity (IEC 61000-4-3)
Fast Transient (IEC 61000-4-4)
Surge (IEC 61000-4-5)
RF Conducted (IEC 61000-4-6)
Magnetic Field (IEC 61000-4-8)
Ingress Protection Code
Radiated and Conducted Emissions EN 5011 Class A
Agency Certifications
Description
Temperature
Humidity
Temperature
Humidity
Altitude
Shock
(IEC 68-2-27)
Vibration
(IEC 68-2-6)
Pollution Degree
For more information visit: www.eaton.com
Communication to EtherNet/IP
consuming one address.
Supports Boot P, DHCP and static
IP addressing.
10/100 BaseT Connection.
Provides for control of all IT.
communicating devices connected
to the network adapter.
Single button press auto configures
the gateway, setting up the system
for default operation.
Advanced configuration using
CH Studio.
PLC, I/O & Communications Products
IT. Connect
Communication Adapters (D77D Series) — EtherNet/IP Adapter
Specification
-58° – 176°F (-50° – 80°C)
5 – 95% non-condensing
-13° –149 °F (-25° – 65°C)
5 – 95% non-condensing
Above 6,600 ft. (2,000m)
consult factory
15G any direction for
11 mS
5 – 150 Hz, 5G .7 mm
maximum peak-to-peak
2
Specification
Modbus Conformance Tested
± 8 kV air, ± 4 kV contact
10V/m 80 – 1,000 MHz, 80% amplitude modulation @ 1 kHz
± 2 kV supply and control, ± 1 kV communications
± 1 kV line-to-ground, ± 2 kV line-to-line
10V, .15 – 80 MHz
30A/m, 50 Hz
IP20
UL 508, CUL (CSA C22.2 No. 14), CE (Low Voltage Directive),
■
■
■
■
■
■
■
■
Table 50-40. EtherNet/IP Specifications
Description
Connections
I/O Size
Baud
Addressing
Channels
Provides for backplane and
interconnect cable connections
to motor control products.
Two independent ports.
Powered from backplane.
Isolated from EtherNet/IP.
Status LEDs for EtherNet/IP and
module health.
Provides for configuration of I/O
devices over EtherNet/IP.
Small package size.
DIN-rail mountable.
Specification
10/100 BaseT
504 bytes Input
504 bytes Output
Ethernet 10/100 Megabit
Ethernet – Boot P, Static IP
or DHCP
2 Independent
Channels
50-27
50