LPAX0600 Red Lion Controls, LPAX0600 Datasheet - Page 4
![Multifunction Meter](/photos/21/38/213824/4244352_sml.jpg)
LPAX0600
Manufacturer Part Number
LPAX0600
Description
Multifunction Meter
Manufacturer
Red Lion Controls
Type
Counter/Rate Indicatorr
Datasheet
1.LPAX0600.pdf
(4 pages)
Specifications of LPAX0600
No. Of Digits / Alpha
6
Panel Cutout Height
3.63"
Panel Cutout Width
9.29"
Signal Input Type
Count And Rate, Serial Slave
Application
For industrial
Connection Type
Cage-Clamp
Cut Out, Panel
9.29×3.63 "
Digit Height
1.5
Dimensions
10"L×4.77"W×4.75"H
Display Digit Height
1.5 "
Display Type
LED
Function
Counter/Rate Indicator/Serial Slave
Humidity
0 to 85%
Material, Casing
Steel
Number Of Digits
5
Primary Type
Electronic
Range, Measurement
-99999 to 999999
Temperature, Operating
0 to +50 °C
Termination
Cage Clamp
Voltage, Input
85 to 250 VAC
Voltage, Supply
85 to 250 VAC/11 to 36 VDC or 24 VAC
Sealing
NEMA 4/IP65
Character Size
1.5"
Color
Red
Ip/nema Rating
IP65 / NEMA 4
Rohs Compliant
Yes
For Use With
Red Lion MPAXI000, MPAXC000 And MPAXR000 MPAX Modules
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
LPAX DISPLAY INSTALLATION
enclosure. The display is provided with a gasket to provide a water-
tight seal. The recommended minimum panel thickness for
NEMA 4/IP65 sealing is 0.060" (1.57 mm).
dimensions shown. The supplied template may be used to
mark the cut-out and hole locations on the panel. After
the panel cut-out has been deburred, slide the panel
gasket over the rear of the display and onto the
mounting studs. Insert the display into the panel cut-
out as illustrated in Figure 3. Install six # 10-32 keps
nuts (supplied) and tighten evenly for uniform
gasket compression. Do not over-tighten the nuts.
LPAX can be surface-wall mounted, suspended, or
bottom mounted. Separate installation instructions are
provided with the mounting accessories.
Environment And Cleaning
not exceed the maximum operating temperature and
provides good air circulation. Placing the system near
devices that generate excessive heat should be avoided.
neutral soap product. Do NOT use solvents. Continuous
exposure to direct sunlight may accelerate the aging process of the bezel.
capabilities of our PAX Series Intelligent Panel Meters. Therefore, you will find
the appropriate PAX information packed with the MPAX Module. Simply
follow the instructions to wire and program the display for your application.
2.0 INSTALLING THE DISPLAY
3.0 WIRING AND PROGRAMMING THE DISPLAY
The LPAX display is intended to be mounted into a panel or
For panel mounting, prepare the panel cut-out to the
By using additional mounting accessories, the
The display should be installed in a location that does
The bezel should be cleaned only with a soft cloth and
Once assembled, the LPAX and MPAX have all the same functions and
ORDERING INFORMATION
Accessories
*Refer to “Selecting Your Display Components and Option Cards.”
**Available as a FREE download from the Red Lion website. www.redlion.net
Optional
Display
Module
Plug-In
Digital
Cards
TYPE
Input
MODEL NO.
PAXCDC
SFCRD
PAXCDL
PAXRTC
SFPAX
PAXCDS
MPAX
LPAX
ENC9
SHR
MB
**
**
*
*
*
6-Digit Display for Digital MPAX Modules
6-Digit Display for MPAXCK (Clock/Timer) and MPAXTM Only
Count/Rate Indicator Module, AC Powered
Count/Rate Indicator Module, DC/24 VAC Powered
Count Indicator Module, AC Powered
Count Indicator Module, DC/24 VAC Powered
Rate Indicator Module, AC Powered
Rate Indicator Module, DC/24 VAC Powered
Clock/Timer Module, AC Powered
Clock/Timer Module, DC/24 VAC Powered
Timer Module, AC Powered
Timer Module, DC/24 VAC Powered
Dual Setpoint Relay Output Card
Quad Setpoint Relay Output Card
Quad Setpoint Sinking Open Collector Output Card
Quad Setpoint Sourcing Open Collector Output Card
RS485 Serial Communications Output Card with Terminal Block
Extended RS485 Serial Communications Output Card with Dual RJ11 Connector
RS232 Serial Communications Output Card with Terminal Block
Extended RS232 Serial Communications Output Card with 9 Pin D Connector
DeviceNet Communications Card
Modbus Communications Card
Extended Modbus Communications Card with Dual RJ11 Connector
Profibus-DP Communications Card
Analog Output Card
Real Time Clock Card for MPAXCK (Clock/Timer) Only
Crimson 2 PC Configuration Software for Windows 98, ME, 2000 and XP (for MPAXI)
PC Configuration Software for Windows 95/98 on 3.5
NEMA 4 Enclosure for LPAX
Shroud for LPAX
Mounting Bracket for LPAX
DESCRIPTION
TROUBLESHOOTING
Figure 3, Installing The LPAX Into A Panel
For technical assistance, contact technical support.
"
disk (for MPAXCK and MPAXTM)
PART NUMBERS
MPAXCK00
MPAXCK10
MPAXTM00
MPAXTM10
MPAXC000
MPAXC010
MPAXR000
MPAXR010
LPAXCK00
PAXCDC1C
PAXCDC2C
PAXCDC4C
LPAX0600
MPAXI000
MPAXI010
PAXCDS10
PAXCDS20
PAXCDS30
PAXCDS40
PAXCDC10
PAXCDC20
PAXCDC30
PAXCDC40
PAXCDC50
SFCRD200
SHRLPAX0
PAXCDL10
PAXRTC00
MBLPAX00
ENC90000
SFPAX