MPAXD000 Red Lion Controls, MPAXD000 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
MPAXD000
Manufacturer Part Number
MPAXD000
Description
Voltage-Current Input Module
Manufacturer
Red Lion Controls
Specifications of MPAXD000
Accessory Type
Analog Input Module
Signal Input Type
Selectable Voltage
No. Of Analog Outputs
5
Character Size
0.56"
Accuracy
0.03% of reading + 0.03 μA to 0.5% of reading + 0.3 μA @ 18 to 28 °C, 0.03% of reading +30 μV to 0.05% of reading +30 mV @ 18 to 28 °C, 0.05% of reading +30 Megohm to 0.05% of reading +1 Ohms @ 18 to 28 °C
Brand/series
MPAX Series
Display Type
LED
Impedance, Input
100 Ohms to 10 Kiloohms
Measuring Range
± 200 μADC to ± 2 ADC, ± 200 mVDC to ± 300 VDC, 100 Ohms to 10 Kiloohms
Resolution
10 nA to 0.1 mA, 10 μV to 10 mV, 0.01 Ohms to 1 Ohms
Standards
cULus Listed, CE Certified
Voltage, Working
85 to 250 VAC
Sealing
NEMA 4/IP65
No. Of Analog Inputs
5
Rohs Compliant
Yes
For Use With
EPAX 5 Digit Displays
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Signal Jumper
is installed. For voltage signals, remove the jumper from the board. (For 2 V
inputs, this removed jumper can be used in the “2 V only” location.)
Couple Jumper
is removed from the board. If DC couple is used, then the jumper is installed.
Bridge Excitation
range. Use the 5 V excitation with high output (3 mV/V) bridges. The 5 V excitation also reduces
bridge power compared to 10 V excitation.
PAXP Jumper Selection
PAXH Jumper Selection
PAXS Jumper Selection
One jumper is used for the input signal type. For current signals, the jumper
One jumper is used for AC / DC couple. If AC couple is used, then the jumper
One jumper is used to select bridge excitation to allow use of the higher sensitivity 24 mV input
A maximum of four 350 ohm load cells can be driven by the internal bridge excitation voltage.
CAUTION: To maintain the electrical safety of the meter, remove
unneeded jumpers completely from the meter. Do not move the
jumpers to positions other than those specified.
Main
Circuit
Board
CURRENT
VOLTAGE
Jumper
Locations
JUMPER SELECTIONS
The
RANGES
JUMPER SELECTIONS
The
indicates factory setting.
indicates factory setting.
2 V ONLY
CURR/VOLT
AC/DC COUPLE
USER INPUT
SIGNAL
9
Input Range Jumper
the following ranges, set the jumpers as stated:
Avoid placing a jumper across two ranges.
For most inputs, one jumper is used to select the input range. However, for
5 A: Remove all jumpers from the input range.
2 V: Install one jumper in “.2/2V” position and one jumper in “2 V only”.
All Other Ranges: One jumper in the selected range only.
Do not have a jumper in both the voltage and current ranges at the same time.
Main
Circuit
Board
JUMPER SELECTIONS
The
BRIDGE
Main
Circuit
Board
JUMPER
LOCATION
indicates factory setting.
USER INPUT
JUMPER
LOCATION
JUMPER
LOCATION
INPUT RANGE
USER INPUT