C200H-CN229-EU Omron, C200H-CN229-EU Datasheet - Page 18

• Manufacturer Part Number: C200H-CN229-EU
• Description: Program Download Cable, For NT20S Graphical LCD Touch Screen, 1.6 Foot, 9 To 9, PC To NT
• Manufacturer: Omron

Specifications of C200H-CN229-EU

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Position Control with Pulse Outputs
(Transistor Output Models Only)
The CPM2B PLCs with transistor outputs have two outputs that
can produce 10 Hz to 10 kHz pulses (single-phase outputs).
When used as single-phase pulse outputs, there can be two
outputs with a frequency range of 10 Hz to 10 kHz with a fixed
duty ratio or 0.1 to 999.9 Hz with a variable duty ration (0 to
100% duty ratio).
Note: With single-phase pulse outputs, pulse outputs 0 and 1 can each be output independently.
J HIGH-SPEED INPUT CAPABILITIES FOR
High-speed Interrupt Input Function
There are four inputs used for interrupt inputs (shared with
quick-response inputs and interrupt inputs in counter mode) with
a minimum input signal width of 50 µs and response time of 0.3
ms. When an interrupt input goes ON, the main program is
stopped and the interrupt program is executed.
Quick-response Input Function
There are four inputs used for quick-response inputs (shared with
interrupt inputs and interrupt inputs in counter mode) that can
reliably read input signals with a signal width as short as 50 µs.
Stabilizing Input Filter Function
The input time constant for all inputs can be set to 1 ms, 2 ms, 3
ms, 5 ms, 10 ms, 20 ms, 40 ms, or 80 ms. The effects of
chattering and external noise can be reduced by increasing the
input time constant.
J OTHER CONVENIENCE FUNCTIONS
Interval Timer Interrupts
The interval timer can be set between 0.5 and 319,968 ms and
can be set to generate just one interrupt (one-shot mode) or
periodic interrupts (scheduled interrupt mode).
Item
Controlling
instruction(s)
Output
number
Output frequency
range
Duty ratio
u be
Pulse outputs
MACHINE CONTROL
01000
01001
Pitch
Single-phase pulse out-
put without accel/decel
pu
PULS(65) and SPED(64)
Pulse output 0
(See Note)
Pulse output 1
(See Note)
10 Hz to 10 kHz
10 Hz
50%
ou acce /dece
Stepping motor
Variable duty-ratio
pulse output
pu se ou pu
PWM(----)
Pulse output 0
(See Note)
Pulse output 1
(See Note)
0.1 Hz to 999.9 Hz
0.1 Hz
0 to 100%
SmartStep
Servodriver
When used as pulse plus direction or up/down pulse outputs,
there can be just one output with a frequency range of 10 Hz to
10 kHz.
Analog Settings
There are two controls on the CPU Board that can be turned to
change the analog settings (0 to 200 BCD) in IR 250 and IR 251.
These controls can be used to easily change or fine-tune
machine settings such as a conveyor belt’s pause time or feed
rate.
DIP Switch Inputs
A DIP switch is provided that controls the status of four input bits.
Calendar/Clock
The built-in clock (accuracy within 1 minute/month) can be read
from the program to show the current year, month, day, day of the
week, and time. The clock can be set from a Programming
Devices (such as a Programming Console) or the time can be
adjusted by rounding up or down to the nearest minute.
Long-term Timer
TIML (—) is a long-term timer that accommodates set values up
to 99,990 seconds (27 hours, 46 minutes, 30 seconds). When
combined with the SECONDS TO HOURS conversion instruction
HMS (—), the long-term timer provides an easy way to control
equipment scheduling.
Single-phase pulse output with trapezoidal
acceleration/deceleration
Pulse + direction output
PULS(65) and ACC(----)
Pulse
output 0
output 0
10 Hz to 10 kHz
10 Hz
50%
Micro Controller Board
Pulse output
Direction output
CPM2B
Up/down pulse output
Pulse
output 0
output 0
10 Hz to 10 kHz
10 Hz
50%
CW pulse out-
put
CCW pulse
output
A--87