WLCLG Omron, WLCLG Datasheet - Page 39

• Manufacturer Part Number: WLCLG
• Description: LIMIT SWITCH, ROD
• Manufacturer: Omron

Specifications of WLCLG

• Operating Force Max: 1.39N
• Contact Voltage Ac Max: 500V
• Contact Voltage Dc Max: 250V
• Contact Current Ac Max: 10A
• Contact Current Dc Max: 10A
• Switch Terminals: Screw
• Svhc: No SVHC (15-Dec-2010)
• Actuator Type: Rod

WL
Changing the installation position
of the actuator
By loosening the Allen-head bolt on
the actuator lever, the position of the
actuator can be set anywhere within
the 360_. With Lamp-equipped
Switches, the actuator lever comes
in contact with the top of the lamp
cover, so use caution when rotating
and setting the lever. When the lever
only moves forwards and backwards,
it will not contact the lamp cover.
Changing the orientation of the
Head
By removing the screws in the four
corners of the Head, the Head can
be set in any of the four directions.
Be sure to change the plunger for
internal operations at the same time.
(The operational plunger does not
need to be changed on overtravel
general-purpose and high-sensitivity
models.) The roller plunger can be
set in either two positions at 90_.
WLCA2-2N and WL01CA2-2N can
only be set in either the forward or
backward direction.
Changing the operating direction
By removing the Head on models
which can operate on one-side only,
and then changing the direction of
the operational plunger, one of three
operating directions can be selected.
In the case of overtravel models, as
noted on page 20, by loosening the
rubber holder using either a coin or a
flat-blade screwdriver, and changing
the direction of the internal rubber
section, one of three operating
directions can be selected.
The tightening torque for the screws
on the Head is 0.78 to 0.88 N S m. (8
to 9 kg S cm)
Installing the roller on the inside
By installing the roller lever in the
opposite direction, the roller can be
installed on the inside. (Set so that
operation can be completed within a
180_ level range.)
Application Variations
Item
Roller Levers: WLCA2, WL01CA2,
WLH2, WL01H2, WLG2, WL01G2
Adjustable Roller Levers: WLCA12,
WL01CA12, WLH12, WL01H12,
WLG12, WL01G12
Adjustable Rod Levers: WLCL,
WL01CL, WLHL, WL01HL, WLGL,
WL01GL
Roller Levers: WLCAj, WL01CAj,
WLGCAj
Adjustable Rod Levers: WLCL,
WL01CL
Horizontal Plungers: WLSDj,
WL01SDj
Roller Plungers: WLD2, WL01D2
Sealed Roller Plungers: WLD28,
WL01D28.
Note: Does not include -RP60
Roller Levers: WLCAj, WL01CAj
Adjustable Roller Levers: WLCA12,
WL01CA12
Adjustable Rod Levers: WLCL,
WL01CL
Overtravel Models: WLCAj-2N,
WL01CAj-2N
Note: The diagram at the right is not
Roller Levers: WLCAj, WL01CAj,
except for the adjustable roller
levers.
Fork Lever Locks: WLCA32-4j,
WL01CA32-4j
Appropriate model/actuator
Series or -141 Series.
correct for the overtravel -2N
models.
Operating
For details on overtravel -2N models, refer to page 19.
Loosen the
Allen-head bolt.
The output of the
Switch will be changed,
regardless of which
direction the lever is
pushed.
Operation in
both directions
Head
Operating
Not operating
Loosen the screws.
Clockwise operation
Loosen the M5 × 12 bolt, set the
actuator’s position and then tighten
the bolt again.
Details
Operating
The output of the
Switch will only be
changed when the lever
is pushed in one
direction.
Operating
Counterclockwise
operation
Not operating
Head
Loosen
the
screws.
Operational
plunger
WL
39