88-SUPER-3/4X66FT 3M, 88-SUPER-3/4X66FT Datasheet - Page 2

• Manufacturer Part Number: 88-SUPER-3/4X66FT
• Description: TAPE, INSULATION, PVC, 0.75INX66FT
• Manufacturer: 3M
• Type: Electricalr

Specifications of 88-SUPER-3/4X66FT

• Tape Backing Material: PVC
• Roll Length: 66ft
• Tape Type: Electrical Insulation
• Width: 0.75"
• Color: Black
• Adhesion To Backing: 25 Oz-in. @ 22 °C
• Adhesion To Steel: 25 oz-in. @ 22 °C
• Elongation: 250% @ 22 °C
• Length, Tape: 66 ft.
• Material, Tape: PVC
• Standards: UL Listed and CSA Certified
• Temperature Rating: +80 °C
• Thickness, Tape: 8.5 mils
• Voltage, Rating: 600 V
• Width, Tape: 3⁄4 in.
• Rohs Compliant: Yes
• Lead Free Status / Rohs Status: RoHS Compliant part

Electrical Properties:
Voltage Rating
UL 510
Dielectric Breakdown
ASTM D1000
Standard Condition
High Humidity Condition
Insulation Resistance
ASTM D1000
(High Humidity Method)
Note: These are typical values and should not be
used for specification purposes.
Specification
Product
The tape is based on polyvinyl chloride (PVC)
and/or its copolymers and has a rubber-based,
pressure-sensitive adhesive. The tape shall be 8.5
mils thick, and be UL Listed and marked per UL
Standard 510 as “Flame Retardant, Cold and
Weather Resistant.” The tape must be applicable at
temperatures ranging from 0˚F through 100˚F (-
18˚C through 38˚C) without loss of physical
properties. The tape shall be classified for use in
both indoor and outdoor environments. The tape
shall be compatible with synthetic cable
insulations, jackets and splicing compounds. The
tape will remain stable and will not telescope more
than 0.1 inches when maintained at temperatures
below 120˚F (50˚C).
Engineering/Architectural
Specification
Primary electrical insulation (branch wiring in wet
or dry locations): All splices for 600 volt wire rated
105˚C (220˚F) and below shall be insulated with a
minimum of two half-lapped layers of Scotch
Super 88 Vinyl Electrical Tape. All connectors
having irregular surfaces shall be padded with
3M, Scotch and Scotchfil are trademarks of 3M.
Electrical Products Division
6801 River Place Blvd.
Austin, TX 78726-9000
www.3M.com/elpd
>1 x10
90% of Standard
10000 volts
6
megohms
®
600V
Scotchfil
Rubber Splicing Tape prior to insulating with Scotch
Super 88 Vinyl Electrical Tape.
Mechanical protection (outer jacketing)
All rubber and thermoplastic insulating high voltage
power cable tape splices and repairs shall be
overwrapped with at least two half-lapped layers of
3M Super 88 Vinyl Electrical Tape.
Installation Techniques
The tape shall be applied in half-lapped layers with
sufficient tension to produce a uniform wind (for
most applications this tension will reduce the tape’s
width to approximately 5/8 of its original width). On
pigtail splices, the tape shall be wrapped beyond the
end of the wires and then folded back, leaving a
protective cushion to resist cut-through. Wrap tape
up-hill, taping from a smaller diameter surface to a
larger diameter surface. Apply the tape with no
tension on the last wrap to prevent flagging.
Shelf Life
Scotch
shelf life (from date of manufacture) when stored
under the following recommended storage
conditions. Store behind present stock in a clean dry
place at a temperature or 70˚F (21˚C) and 40-50%
relative humidity.
Availability
Scotch
from your local 3M authorized distributor in the
following standard roll sizes:
3/4 in. x 66 ft.
3/4 in. x 44 ft.
3/4 in. x 36 yd.
1-1/2 in. x 44 ft.
1-1/2 in. x 36 yd.
Other lengths and widths are available by special
request.
®
®
Super 88 Vinyl Electrical Tape has a 5 year
Super 88 Vinyl Electrical Tape is available
™
Electrical Insulation Putty or 3M 130C
©3M IPC 2001 78-8124-4857-5-C
Litho in USA