467MP (12 IN X 60 YD) 3M, 467MP (12 IN X 60 YD) Datasheet - Page 3

• Manufacturer Part Number: 467MP (12 IN X 60 YD)
• Description: TAPE, ADHESIVE ACRYLIC CLR/TAN 12INX60YD
• Manufacturer: 3M

Specifications of 467MP (12 IN X 60 YD)

• Tape Backing Material: Acrylic
• Roll Length: 60yard
• Features: 3M Adhesive 200MP
• Tape Type: Graphic/Overlay Attachment
• Width: 12"
• Color: Clear W/Tan Liner
• Rohs Compliant: Yes

3M
467MP • 468MP • 467MPF • 468MPF • 7952MP • 7955MP
7962MP • 7965MP • 9172MP • 9185MP • 9667MP • 9668MP
Constructions
(continued)
Typical Physical
Properties and
Performance
Characteristics
™
High Performance Adhesive Transfer Tapes with Adhesive 200MP
Note: The following technical information and data should be considered representative
I. Adhesion to Stainless Steel
ASTM D3330 modified (90° peel, 2 mil aluminum foil backing)
Dwell
15 minute room temperature (RT)
72 hour RT
72 hour 158°F (70°C)
72 hour RT - 180° peel, 2 mil al foil
II. Adhesion to Other Surfaces
ASTM D3330 modified (90° peel, 2 mil aluminum foil backing)
Dwell
72 hour RT aluminum
72 hour RT ABS
72 hour RT acrylic
72 hour RT glass
72 hour RT polycarbonate
72 hour RT rigid PVC (unplasticized)
Liner Configuration Guide:
The polycoated kraft liners are more resistant to humidity curl and wrinkling than standard
plain paper liners. The film liners are the most resistant to the negative effects of humidity.
Adding Liners for 3M™ Adhesive 200MP:
General purpose steel rule die-cutting
Steel rule cutting nested or multi-up nameplates
Kiss cutting, steel rule
Rotary die-cutting
Selective die-cutting (cut adhesive before laminate)
Thermoforming
Part inspection
Embossed parts
Metal parts (punch press)
1. Rotary processing, adhesive only, on a densified
2. Rotary processing for finished parts. It is most efficient to
5
The outside of liner 4994 has the most premium silicone release (easiest release). Typical
release, of the outside of liner 4994, from 3M adhesive 200MP after lamination (both
before and after heat aging) is 5-10 grams/inch. For slightly higher liner release, typical
values for the inside of the liner 4994 are 15-20 grams/inch when laminated to the 3M
adhesive 200MP.
or typical only and should not be used for specification purposes.
on common sheet
kraft liner. In this process the adhesive will stay with
the 58# PCK liner, leaving adhesive die-cuts
dispensable from the densified kraft liner 4994.
use 3M™ Adhesive Transfer Tapes 467MPF or 468MPF.
If a densified kraft (DK) liner is necessary, the adhesive
should be first laminated to the substrate with pressure.
After lamination, remove the 58# PCK liner and laminate
the inside of the liner 4994 (DK). Current process limitations
prevent the supply of the 3M adhesive 200MP on a DK liner.
- 3 -
ounces/inch N/100mm ounces/inch N/100mm
ounces/inch N/100mm ounces/inch N/100mm
2 mil (0.002 inches)
2 mil (0.002 inches)
168
77
62
61
80
58
52
47
82
77
184
84
68
67
88
63
57
51
90
84
outside of 3M™ liner 4994
58# polycoated kraft (PCK)
polycoated glassine (PCG)
inside of 3M™ liner 4994
polyester or DK added
polyester (PET) and
5 mil (0.005 inches)
5 mil (0.005 inches)
white, PP, HDPE
HDPE, white PP
118
181
133
115
double-linered
66
68
67
92
65
69
HDPE, PET
83# PCK
83# PCK
129
198
146
126
101
72
74
73
71
76
5
5