S1048-TAPE-1X100-FT Tyco Electronics, S1048-TAPE-1X100-FT Datasheet - Page 2
S1048-TAPE-1X100-FT
Manufacturer Part Number
S1048-TAPE-1X100-FT
Description
TAPE, SEALANT, THERMOPLASTIC, 1INX100FT
Manufacturer
Tyco Electronics
Specifications of S1048-TAPE-1X100-FT
Tape Backing Material
Thermoplastic
Roll Length
100ft
Adhesive Material
Thermoplastic
Tape Type
Sealing
Width
1"
Product
Tape
Size
1 in x 100 ft
Description/function
Hot Melt Polyolefin Adhesive
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
S1030 - Hot Melt Adhesive Tape
Introduction
This is a non-flame retarded hot melt black adhesive tape which is based on EVA/polyamide polymers. The tape is often pre-applied to moulded
shapes and the pre-coat designation is /180. It has an operating temperature of -80
low temperatures.
Colour:
Packaging:
Typical Applications
S1030 tape is recommended for marine applications where salt water is a threat. The adhesive is very user-friendly in that it exhibits excellent flow
extremely quickly when heated under normal installation conditions. Not recommended where aggressive solvents may be present. Also not
recommended for terminations under in-service flexural stress at temperatures above 40
substrates and has become the recommended hot melt adhesive for System 100, i.e., Zerohal tubing and cable jackets, -100 moulded shapes.
Recommended with –25 moulded shapes, DR25 tubings, FDR cable jackets, RNF, RW-175, Polyurethane materials. Can be used as a repair adhesive
in conjunction with RP-4800 tubing and also with S1081 harness repair tape.
Installation Guidelines
Prepare surfaces to be bonded by abrading the substrate using 100 Grit Abrasive cloth. Cut required amount of adhesive tape and position as
required. Apply a small amount of heat to secure adhesive tape in place. As a general guide, two wraps of adhesive tape should be applied. When
using adhesive tape with a Raychem Adaptor, the knurled area and the recess lip, should both be applied with the adhesive tape. When second
surface to be bonded is heated and recovered, post heat all bonds for at least 60 seconds. As a general guide the CV 1981 Heat Gun should be on
setting 7 with a PR26 or PR51 Reflector fitted. Allow bonds to cool before flexing.
S1048 - Adhesive Tape
Introduction
S1048 is a hot melt polyolefin based adhesive which primarily is supplied solution coated onto moulded shapes as /86. It is generally used as a high
strength hot melt adhesive. Although upper service temperature is 105
much above 60-70
Colour:
Packaging:
Typical Applications
S1048 will adhere extremely well to most cable jacket materials, ie: ZHTM, DR-25, FDR or RNF as long as enough heat has been applied at the
installation stage to ensure complete flow and wettability of the adhesive. This product will generally give a higher bond strength to most substrates
when compared to S1030.
Installation Guidelines
Prepare surfaces to be bonded by abrading the substrate using 100 Grit Abrasive cloth. Cut required amount of adhesive tape and position as
required. Apply a small amount of heat to secure adhesive tape in place. As a general guide, two wraps of adhesive tape should be applied. When
using adhesive tape with a Raychem Adaptor, the knurled area and the recess lip, should both be applied with the adhesive tape. When second
surface to be bonded is heated and recovered, post heat all bonds for at least 60 seconds. As a general guide the CV 1981 Heat Gun should be on
setting 7 with a PR26 or PR51 Reflector fitted. Allow bonds to cool before flexing. Due to high temperature needed to achieve correct installation, this
adhesive is not recommended for –4 moulded parts or heat sensitive substrates.
T-DR25-Tape
Introduction
DR-25 tape is available for repair and retrofit applications as a tape. It is available in two different widths. Its fluid resistance and mechanical
performance is comparable with DR-25 Tubing.
Colour:
Packaging:
Packaging:
Typical Applications
T-DR-25 Tape is recommended for repairing DR-25 cable jackets, protecting wire bundles and is flame retarded. The tape has a good seal against
splash proof but not for immersion.
Installation Guidelines
Prepare surfaces to be bonded by abrading the substrate using 100 Grit Abrasive cloth. Cut required amount of adhesive tape and position as
required. S1030 tape or S1125 product should be applied at the ends of the tape to give sealing and prevent the DR-25 tape unwrapping. This tape
is not self-amalgamating and only gives a “bond” to itself and the substrate underneath by the grip obtained in the shrinkage during installation. It does
not “bond” in the same way as a self-amalgamating or adhesive tape would. The installation temperature should be in excess of 130
such as a PR12 used with the recommended CV1981 heatgun.
Cat. No. 1773371
o
C. Operating temperature range of -80
Black
10mtr roll
Translucent Yellow
30mtr roll
Black
10 mtr roll
T-DR-25-NR2-0
10 mtr roll
Dimensions:
Width:
Thickness:
Specification:
Dimensions:
Specification:
Dimensions:
Specification:
o
C to 120
T-DR-25-NR1-0
20.0mm
0.45mm
RK6161
o
C.
o
C, terminations should not be under in-service flexural stress at temperatures
Specifications subject to change.
Width: 20mm
Thickness: 0.3mm
RK6017
Width: 25.4mm wide
Thickness: 0.66mm
RK6626/RT1050/6
o
C to +80
o
C. S1030 exhibits good adhesion to a wide range of
Width: 25.0mm
Thickness: 0.6mm
o
C. This product is recommended for high flexibility at
www.tycoelectronics.com
o
C and a reflector