NCP18XW222J03RB Murata, NCP18XW222J03RB Datasheet - Page 28

• Manufacturer Part Number: NCP18XW222J03RB
• Description: NTC THERMISTOR
• Manufacturer: Murata
• Series: NCPr
• Type: NTCr

Specifications of NCP18XW222J03RB

• Thermistor Type: NTC
• Resistance: 2.2kohm
• Thermistor Tolerance: ± 5%
• Beta Value (k): 3950
• Operating Temperature Range: -40°C To +125°C
• Thermistor Case Style: 0603
• No. Of Pins: 2
• Resistance Tolerance: ± 5%
• Tolerance: 5 %
• Termination Style: SMD/SMT
• Package / Case: 0603
• Current Rating: 0.67 mAmp
• Dimensions: 0.8 mm W x 1.6 mm L x 0.8 mm H
• Power Rating: 100 mW
• Beta Upper Temperature: 50°C
• Rohs Compliant: Yes
• Beta Lower Temperature: 25°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
!Note
This product is designed for application in an
ordinary environment (normal room temperature,
humidity and atmospheric pressure).
Do not use under the following conditions because all
these factors can deteriorate the product
characteristics or cause failures and burn-out.
1. Corrosive gas or deoxidizing gas
Be sure to provide an appropriate fail-safe function
on your product to prevent secondary damages that may
be caused by the abnormal function or the failure of
our product.
To keep solderability of product from declining, the
following storage condition is recommended.
1. Storage condition:
2. Storage term:
Use this product within the specified temperature
range.
Higher temperature may cause deterioration of the
characteristics or the material quality of this
product.
1. Be sure that the preheat-up does not melt the
2. Do not touch the body with soldering iron.
(Chlorine gas, Hydrogen sulfide gas, Ammonia gas,
Sulfuric acid gas, Nitric oxide gas, etc.)
Temperature -10 to +40 degree C
Humidity less than 75%RH (not dewing condition)
Use this product within 6 months after delivery by
first-in and first-out stocking system.
soldering of this product. Excessive heat may
cause failure to open, short or insulation break
down.
The soldering point should be min. 5mm away from
the root of lead wire.
!Caution (Storage and Operating Conditions)
!Caution (Others)
Notice (Storage and Operating Conditions)
Notice (Rating)
Notice (Soldering and Mounting)
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
for Temperature Sensor Lead Type/Lead Insulation Type !Caution/Notice
2. Volatile or flammable gas
3. Dusty conditions
4. Under high or low pressure
5. Wet or humid locations
6. Places with salt water, oils, chemical liquids or
7. Strong vibrations
8. Other places where similar hazardous conditions
3. Handling after unpacking:
4. Storage place:
1. The ceramic element of this product is fragile, and
2. Do not apply an excessive force to the lead.
organic solvents
exist
After unpacking, reseal product promptly or store
it in a sealed container with a drying agent.
Do not store this product in corrosive gas
(sulfuric acid gas, chlorine gas, etc.) or in
direct sunlight.
care must be taken not to load an excessive
press-force or not to give a shock at handling.
Such forces may cause cracking or chipping.
Otherwise, it may cause junction between lead and
element to break or crack. Holding element by side
lead wire is recommended when lead wire is bent or
cut.
Notice (Handling)
R44E9.pdf 05.4.13
27
6