E2EM-X2C1 2M Omron, E2EM-X2C1 2M Datasheet - Page 7
![Inductive Proximity Sensor](/photos/20/0/200040/3753436_sml.jpg)
E2EM-X2C1 2M
Manufacturer Part Number
E2EM-X2C1 2M
Description
Inductive Proximity Sensor
Manufacturer
Omron
Datasheet
1.E2EM-X8X1-2M.pdf
(9 pages)
Specifications of E2EM-X2C1 2M
Sensor Input
Inductive
Sensing Range
2mm
Supply Voltage Range Dc
10V To 30V
Sensor Housing
Cylindrical
Supply Voltage Max
30VDC
Sensing Range Max
2mm
Switch Terminals
Wire Leaded
Output Type
NPN, NO
Supply Voltage Min
10VDC
Sensor Output
NPN, NO
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
● Mounting
Tightening Force
Do not tighten the nut with excessive force.
A washer must be used with the nut.
Dimensions
Pre-wired Models (Shielded)
E2EM-X2C@
E2EM-X8@@
15 dia.
13
29 dia.
24
M8 × 1
M18 × 1
3
26
Toothed washer
30
Two clamping nuts
4
8
Shielded Models
1. 4-dia. vinyl-insulated round cable with 2/3 conductors
2. Operation indicator (yellow)
1. 6-dia. vinyl-insulated round cable with
2. X1 Models: Operation indicator (red) Setting
(Conductor cross section: 0.3 mm
Insulator diameter: 1.3 mm), Standard length: 2 m
The cable can be extended up to 200 m
(separate metal conduit).
Indicator *2
38
2/3 conductors (Conductor cross section: 0.5 mm
Insulator diameter: 1.9 mm), Standard length: 2 m
indicator (green)
X2 Models: Operation indicator (red)
C Models: Operation indicator (yellow)
Part B Part A
Toothed washer
43
7
Two clamping nuts
2
10
*1
Indicator *2
12
Unshielded Models
Part B Part A
Mounting Hole
2
,
Dimensions
F
*1
2
,
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
E2EM-X4@@
E2EM-X15@@
Note: 1. The allowable tightening strength depends on the distance from the
Model
M8
M12
M18
M30
Dimensions
21 dia.
F (mm)
17
2. The following strengths assume washers are being used.
42 dia.
edge of the head, as shown in the following table. (A is the distance
from the edge of the head. B includes the nut on the head side. If the
edge of the nut is in part A, the tightening torque for part A applies
instead.)
36
Shielded
M12 × 1
Torque
M30 × 1.5
8.5
4
+0.5
M8
0
33
Toothed washer
Dimension
38
dia.
5
Two clamping nuts
(mm)
2
10
1. 4-dia. vinyl-insulated round cable with 2/3 conductors
2. X1 Models: Operation indicator (red)
9
1. 6-dia. vinyl-insulated round cable with 2/3
2. X1 Models: Operation indicator (red) Setting
Toothed washer
(Conductor cross section: 0.3 mm
Insulator diameter: 1.3 mm), Standard length: 2 m
Setting indicator (green)
X2 Models: Operation indicator (red)
C Models: Operation indicator (yellow)
43
conductors (Conductor cross section: 0.5 mm
Insulator diameter: 1.9 mm), Standard length: 2 m
indicator (green)
X2 Models: Operation indicator (red)
C Models: Operation indicator (yellow)
48
12.5
Two clamping nuts
Part A
Indicator *2
9
M12
+0.5
0
3
10
dia.
180 N·m
Torque
30 N·m
70 N·m
9 N·m
Indicator *2
18.5
12
M18
+0.5
*1
0
dia.
2
,
E2EM
30.5
Torque
12 N·m
Part B
(Unit: mm)
*1
M30
+0.5
0
2
,
dia.
7