PS71-40-4MNZ-C-FL18 Gems Sensors Inc, PS71-40-4MNZ-C-FL18 Datasheet - Page 2

• Manufacturer Part Number: PS71-40-4MNZ-C-FL18
• Description: Pressure Switch
• Manufacturer: Gems Sensors Inc

Specifications of PS71-40-4MNZ-C-FL18

• Contact Voltage Ac Max: 250V
• Peak Reflow Compatible (260 C): No
• Circuitry: SPDT
• Operating Pressure Max: 1000psi
• Port Style: NPT
• Contact Current Ac Max: 5A
• Leaded Process Compatible: No
• Contact Current Max: 5A
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

How To Order
Use the Bold characters from the chart below to construct a product code. Please reference Notes.
1 Pressure Range Code
2 Pressure Fitting
3 Circuit
4 Electrical Termination
Table 1 — Pressure Range Codes
** These numbers are for the standard microswitch. With either the -SP or -10A option, the values are typically 20% greater than those
* Repeatability and set point of units may change due to the effects of temperature.
Pressure Range Code
12L14 Zinc-Plated Steel
316 Stainless Steel
-CABXX = 18 AWG PVC Cable
listed. With the -RD option, the values will be typically 25% less than those listed. In certain applications deadband can be tailored
and controlled to customer specifications. Consult factory for details.
-FLSXX = Flying Leads w/PVC Shrink Tubing
-2MGS = 1/8˝ BSPM (G type)
-4MNS = 1/4˝ NPTM
-4MGS = 1/4˝ BSPM (G type)
-2MNZ = 1/8˝ NPTM
-4MNZ = 1/4˝ NPTM
-2MGZ = 1/8˝ BSPM (G type)
-4MGZ = 1/4˝ BSPM (G type)
-4MSZ = 7/16˝-20 SAE Male
-6MSZ = 9/16˝-18 SAE Male
-FLXX = Flying Leads
-ELXX = 1/2˝ NPT Male Conduit w/Flying Leads
Insert Pressure Range Code from Table 1, below.
-HCR = Right Angle DIN 43650A 9mm
-HNR = Right Angle DIN 43650A with 1/2˝ Female
-HR = Right Angle DIN 43650A Male Half Only
-HN = DIN 43650A with 1/2˝ Female NPT Conduit
-HC = DIN 43650A 9mm Cable Clamp
-SP = Spade Terminals
-A = SPST/N.O.
-B = SPST/N.C.
-C = SPDT
-H = DIN 43650A Male Half Only
10
20
30
40
50
60
Cable Clamp
NPT Conduit
1
3
6
6
2
2500-5000 psi (172.4-344.7 bar)
PS71 -10 -4MNZ -C -H
1000-3000 psi (69-206.8 bar)
5
250-1000 psi (17.2-69.0 bar)
65-300 psi (4.5-20.7 bar)
10-30 psi (0.7-2.1 bar)
25-75 psi (1.7-5.2 bar)
Pressure Range
6
6
Visit www.GemsSensors.com for most current information.
3
1
4
6
6
5 Options
6 Fixed Set Point (optional)
2
-OXY = Oxygen Cleaned
A. Specify set point -FS
B. Set Point Actuation
-WM = Weather Pack Connector, Male
-10A = 10A @ 125/250 VAC Max. Rating
-WF = Weather Pack Connector, Female
-RD = Reduced Differential
-SR = Spiral Restrictor (high damping coefficient)
-DE = Deutsch Connector, Male, DT04 Series
-IP = Ingress Protection
(in PSI or BAR, see example)
R on Rising Pressure
F on Falling Pressure
Example: -FS2BARF for 2 BAR Falling
or -FS20PSIR for 20 PSI Rising
-N = Neoprene Diaphragm
-G = Gold Contacts
-R = Restrictor (low damping coefficient) Brass
-V = Viton
-E = EPDM Diaphragm
±1.5 psi (0.103 bar) +2% of setting
±2.5 psi (0.172 bar) +2% of setting
±5.0 psi (0.345 bar) +2% of setting
±15 psi (1.03 bar) +2% of setting
±30 psi (2.06 bar) +3% of setting
±50 psi (3.45 bar) +4% of setting
7
(for loads less than 12 mA @ 12 VDC)
(25% reduction typical)
300 Series Stainless Steel
3
®
Repeatability*
Diaphragm
4
9
8
-XX -XXXX
5
11
10
20 psig (1.38 bar) +11% of setting
45 psig (3.10 bar) +12% of setting
70 psig (4.83 bar) +12% of setting
140 psi (9.65 bar) +13% of setting
3.5 psi (0.28 bar) +11% of setting
3.5 psi (0.28 bar) +11% of setting
6
Average Deadband**
Notes:
1. Other fittings available.
2. 20% increase in deadband
3. 18˝ is standard. Specify lead
4. 18˝ is standard. Specify
5. 36˝ is minimum. Specify
6. DIN connectors require -C
7. Options -10A, -G or -RD
8. Ingress Protection is
9. Requires stainless steel
10. -SR will result in wider
11. Set Point must be within
Consult factory.
typical.
length in inches (max. 48˝).
e.g. -FL18 or -FLS30.
lead length in inches (max.
48˝). e.g. -EL18 or -EL30.
cable length in inches. e.g.
-CAB36 or -CAB120.
SPDT circuit.
cannot be combined.
available only with -FL, -FLS
or -CAB Electrical
Termination choices.
Ingress Protection requires
Fixed Set Point -FS.
housing.
deadbands and slower
response time.
Pressure Range selected in
Step 1.
mInIaTURE
I-16