QS186E BANNER ENGINEERING, QS186E Datasheet - Page 5

• Manufacturer Part Number: QS186E
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Series: QS18r
• Type: Infraredr

Specifications of QS186E

• Output Current: 100mA
• Supply Voltage Range Dc: 10V To 30V
• Contact Current Max: 100mA
• Switch Terminals: Cable
• Sensor Input: Optical
• Sensing Range Max: 20m
• Sensing Mode: Opposed
• Current, Switching: 100 mA
• Primary Type: Photoelectric
• Technology: Photoelectric
• Sensing Range: 20m
• Sensor Output: PNP
• Rohs Compliant: Yes

Unterminated Plastic Fiber Cutting Procedure
Unterminated plastic fibers are designed to be cut by the user to the length required
for the application. To facilitate cutting, a Banner model PFC-1 cutting device is
supplied with the fiber. Cut the fiber as follows:
1) Locate the “control end” of the fiber (the unfinished end). Determine the length of
2) Double-check the fiber length, and close the cutter until the fiber is cut. Using a
3) Gently wipe the cut ends of the fiber with a clean, dry cloth to remove any
Plastic Fiber Installation
A) Unlock the fiber gripper as shown in Figure 2. If 0.25 mm or 0.5 mm core fibers are
B) Gently insert the prepared plastic fiber ends into the ports, as far as they will go.
C) Slide the fiber gripper back to lock, as shown in Figure 2.
Glass Fiber Installation
A) Install the O-ring (supplied with the fiber) on each end, as shown in the drawing.
B) While pressing the fiber ends firmly into the portson the front of the sensor, slide the
fiber required for the application. If using a bifurcated fiber, separate the two halves
of the fiber at least 2" beyond the fiber cutting location. Lift the top (blade) of the
cutter to open the cutting ports. Insert one of the control ends through one of the
cutting ports on the PFC-1 cutter so that the excess fiber protrudes from the back of
the cutter.
different cutting port, cut the second control end to the required length. To ensure a
clean cut each time, do not use a cutting port more than once.
contamination. Do not use solvents or abrasives on any exposed optical fiber.
being used, slide the small fiber adapters onto the fibers, flush with the fiber ends.
U-shaped retaining clip (supplied with the sensor) into the slot in the sensor’s barrel,
until it snaps into place.
NPN (Sinking) Outputs
QS18 Sensors with
bu (3)
bn (1)
bk (4)
wh (2)
Banner Engineering Corp.
bn
bu
www.bannerengineering.com • Tel: [phone]
QS18 Emitters
Load
Load
Load
Load
10-30V dc
10-30V dc
-
+
+
–
•
Minneapolis, U.S.A.
Installing Fibers
PNP (Sourcing) Outputs
QS18 Sensors with
bn (1)
bu (3)
bk (4)
wh (2)
Load
Load
10-30V dc
+
-
Hookups
(Cable Connector Shown)
4-Pin Pico-Style Pin-out
Black Wire
Blue Wire
Figure 1. PFC-1 plastic fiber cutter
Figure 2. Installing plastic fibers
Figure 3. Installing glass fibers
White Wire
Brown Wire
WORLD-BEAM
Use small ports
for fiber sizes:
• 0.25 mm (0.01")
• 0.5 mm (0.02")
B
(supplied with fiber)
A
(Cable Connector Shown)
4-Pin Euro-Style Pin-out
(1) bn
(4) bk
Retaining Clip
Lift to Open Ports
Use large ports
for fiber sizes:
• 0.75 mm (0.03")
• 1.0 mm (0.04")
• 1.5 mm (0.06")
C
P/N 63908 rev. G
Cutting Ports
4-Large
2-Small
®
O-ring
QS18
wh (2)
bu (3)
5