QS30EDV BANNER ENGINEERING, QS30EDV Datasheet - Page 6

• Manufacturer Part Number: QS30EDV
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Diffuser

Specifications of QS30EDV

• Output Current: 150mA
• Sensor Output: NPN/PNP
• Supply Voltage Range Dc: 10V To 30V
• Sensor Housing: Rectangular
• Sensing Range Min: 1100mm
• Sensor Input: Optical
• Body Material: ABS Plastic
• Supply Voltage Max: 30VDC
• Brand/series: World-Beam®
• Current, Switching: 150 mA
• Function: Proximity
• Ip Rating: IP67
• Mounting Type: Threaded
• Output: NPN/PNP
• Primary Type: Photoelectric
• Range, Measurement: 1100 mm
• Sensing Mode: Diffuse
• Technology: Photoelectric
• Termination: 5-Wire Cable
• Voltage, Supply: 30 VDC

• Sets a threshold 12.5% below the taught condition.
• Any condition darker than the threshold condition causes the output to change state.
• Threshold position is adjustable using the “+” and “-” buttons (Manual Adjust).
• Recommended for applications where only one condition is known, for example a stable
A single sensing condition is presented, and the sensor positions a threshold 12.5%
below the presented condition. When a condition darker than the threshold is sensed, the
output either turns ON or OFF, depending on the Light/Dark Operate setting (see SETUP
mode, page 8).
Light SET and Light/Dark Operate Selection
In Light Operate mode, Light SET teaches the Output ON condition. In Dark Operate
mode, Light SET teaches the Output OFF condition.
WORLD-BEAM
6
light background with varying darker targets.
P/N 127755 rev. B
• Press and hold Static push
• Present sensing condition
• Four-click Static push button
0.04 seconds ≤ “Click” ≤ 0.8 seconds
button > 2 seconds
Push Button
or
T
T
T
®
Single-Point Light SET
QS30EDV
T
• Single-pulse remote line
• Present sensing
• Four-pulse remote line
0.04 seconds ≤ T ≤ 0.8 seconds
condition
or
T T T
T
T
Remote Line
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Power LED: OFF
Output LED: ON (Push Button)
Output LED: OFF (Remote)
Bargraph
Threshold Condition Accepted
Power LED: ON
Bargraph: Indicators #5–8 flash together
Sensor returns to RUN mode with new settings
Threshold Condition Unacceptable
Power LED: OFF
Bargraph:
Sensor returns to “SET Sensing Condition”
T T T
T
T
T
T
T
T
T
T
T
T
T
: #5 and 6 alternately
T
flash
to show that the threshold
condition is accepted
#1, 3 and 5, 7 alternately flash
to show failure
T
T
T
T
T
T
Banner Engineering Corp. • Minneapolis, MN U.S.A.
T
www.bannerengineering.com • Tel: [phone]
T
T
Figure 5. Single-Point Light SET (Light
T
(no signal)
(no signal)
(no signal)
Darkest
Darkest
Darkest
T
the presented condition
T
threshold 12.5% above
Output OFF
T
Result
Sensor positions
T
Output OFF
Output OFF
Operate shown)
T
T
Presented
Condition
Threshold position
Threshold position
Manual Adjust
Manual Adjust
adjusted by
adjusted by
Output ON
Presented
Condition
Condition
Presented
Push Button
Sensor positions
threshold 12.5% below
the presented condition
Remote
Output ON
Output ON
static
static
static
static
Output OFF
dynamic
dynamic
dynamic
dynamic
Most Light
Most Light
Most Light
(saturated
(saturated
(saturated
signal)
signal)
signal)