HDJD-S822-QR999 Avago Technologies US Inc., HDJD-S822-QR999 Datasheet

Page 1

... HDJD-S822-QR999 RGB Color Sensor Data Sheet Description HDJD-S822-QR999 is a high performance, small in size, cost effective light to voltage converting sensor. The sensor combines a photodiode array and three tran- simpedance amplifiers in a single monolithic CMOS IC solution. With a Red (R), Green (G) and Blue (B) color filters coated over the photodiode array, the sensor converts RGB light to analog voltage outputs, denoted by VROUT, VGOUT and VBOUT, respectively ...

Page 2

Package Dimensions Note: Dimensions are in millimeters (mm)  ...

Page 3

... Part Numbering Systems HDJD Gain Selection (GS) Option 999: GS 00, 01 Packing Type R: Tape and Reel Product Packaging Q: QFN Product Component without IR filter Pin Out for HDJD-S822-QR999 Pin Pin Name Normal Operation Pin  VDD5 Supply Pin  GND Ground Pin  GSGRN0 Gain Selection Green bit 0 ...

Page 4

Theory of Operation The integral R,G,B color filters on the photodiode array detect the R,G,B components of the light falling on the sensor. The photodiode convert the R,G,B light components into photocurrents. The integrated transimpedence amplifiers for R,G,B components then converts the photocurrent to analog voltage outputs. The voltage output of each R,G,B channel increases linearly with increasing light intensity. Sensor IC Block Diagram [1,2] Absolute Maximum ...

Page 5

Recommended Operating Conditions Parameter Symbol. Operating Temperature T A Supply Voltage V DD Operating Conditions and Electrical Requirements Electrical Characteristics 5V Parameter Symbol Dark voltage V D Maximum output voltage swing V O MAX Supply ...

Page 6

Parameter Symbol Remark [4] GS:00 l Saturation Irradiance (Blue Channel) GS:00 l (Green Channel) GS:00 l (Red Channel) [4] GS: l Saturation Irradiance (Blue Channel) GS: l (Green Channel) GS: l (Red Channel) [4] GS:0 l Saturation Irradiance (Blue Channel) ...

Page 7

Gain Selection Feedback Resistor Table GSRED1 GSRED0 GSGRN1 Notes: 1. Gains selections, GS: Bit 1 Bit 0 are applicable for each Red, Green and blue Channel. 2. Gain selections for each channel can be selected independently of each other. 3. Feedback resistor value is proportional to responsivity. Refer to block diagram below indicates that the pin is connected to ground. 1 indicates no connection. GS (1:0) FEEDBACK RESISTOR ...

Page 8

... GS: Irradiance - Ee (mW/cm Figure 4. Voltage output of green channel vs irradiance ( Recommended Reflow Profile It is recommended that Henkel Pb- free solder paste LF310 be used for soldering HDJD-S822-QR999. Below is the rec- ommended reflow profile. 230 ± 5°C T-peak 218°C T-reflow DEL TA-FLUX = 2 °C/sec. max. 160°C T-max. 120°C T-min. DEL TA-RAMP = 1°C/sec. max. ...

Page 9

Lead QFN Recommended PCB Land Pad Design IPC-SM-782 is used as the standard for the PCB land pad design. Recommended PCB finishing is Gold. 0 Lead QFN Recommended Stencil Design A stencil thickness of 2.18mm (6 mils) for this QFN package is recommended. 0 0.8 mm 3.19 mm 3.19 mm 3.9 mm 5.5 mm 0.8 mm 0.8 mm 2.18 mm ∅ ...

Page 10

... Recommendations for Handling and Storage of HDJD-S822-QR999 This product is qualified as Moisture Sensitive Level 4 per Jedec J-STD-020. Precautions when handling this moisture sensitive product is important to ensure the reli- ability of the product. Do refer to Avago Application Note AN5305 Handling Of Moisture Sensitive Surface Mount Devices for details. A. Storage before use • Unopened moisture barrier bag (MBB) can be stored at 30° ...

Page 11

R10.65 R5.2 45° EMBOSSED RIBS RAISED: 0.25 mm WIDTH: 1.25 mm NOTES: 1. *MEASURED A T HUB AREA. 2. ALL FLANGE EDGES TO BE ROUNDED. For product information and a complete list of distributors, please go to our web site: ...