LT3NIQ BANNER ENGINEERING, LT3NIQ Datasheet
LT3NIQ
Specifications of LT3NIQ
Related parts for LT3NIQ
LT3NIQ Summary of contents
Page 1
WARNING . . . ! Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death. These sensors do NOT include the self-checking redundant circuitry ...
Page 2
... LED is still ON solid. 2 P/N 68504 rev. C Retro, Analog/Discrete Laser Lenses Target Emitter E R Receiver Element Banner Engineering Corp. www.bannerengineering.com • Tel: 763.544.3164 SIGNAL OUTPUT Signal LED Output LED FAST Response Speed Response Speed SPEED MED Push Button ...
Page 3
... Far Window Window Target Position Figure 3. Analog output as a function of target position Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 LT3 Time-of-Flight Sensor – Window Limits Window limits may be taught to the sensor in several ways, either using the push buttons on the top of the sensor or via a remote switch ...
Page 4
... Sensor learns first limit and Discrete Output waits for second limit • Single-pulse the remote line • Appropriate TEACH LED goes OFF • Sensor learns second limit and returns automatically to RUN mode Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 T T ...
Page 5
... Sensor will return to RUN mode if first TEACH condition is not registered within 120 seconds. ** Press and hold the same push button (or hold the remote line high) > 2 seconds (before teaching the second limit) to exit PROGRAM mode without saving any changes. The sensor will revert to the last saved program. Banner Engineering Corp. Minneapolis, MN U.S.A. • ...
Page 6
... Sensor is operating normally (power ON, Laser enabled) 6 P/N 68504 rev. C Retro, Analog/Discrete Result • Push buttons are either enabled or disabled, depending on previous condition Indicates Indicates Selected Laser Response Speed Enable Time Slow 150 ms Medium 60 ms Fast 51 ms Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 7
... Factory defaults: Slow response speed (100 ms discrete, 2.5 Hz analog) Laser Control Connect red wire 24V dc to enable laser beam; connect +1.8V dc (or open connection) to disable. See page 6 for delay times on enable. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 LT3 Time-of-Flight Sensor – ...
Page 8
... Slow optical instruments for intrabeam viewing. Reference 60825-1 Amend. 2 © IEC:2001(E), section 8. Figure 5. Class 1 laser label and precautions Banner Engineering Corp. www.bannerengineering.com • Tel: 763.544.3164 LASER LIGHT CLASS 1 LASER PRODUCT RADIANT POWER 0.15mW 10ns PULSE, 1MHz nm Complies with IEC 60825-1:2001 and 21 CFR 1040.10 & ...
Page 9
... Press Teac h button. (Teach flas shes ess T each b utt o n. (Teach turns OFF . .) 48.8 mm (1.92") 19.5 mm (0.76") 5.2 mm (0.20") 2x ø4.5 mm (0.18") C'sink ø7.3 mm (0.29"), 5.3 mm (0.21") deep Hookups Retro, Analog/Discrete LT3NIQ 12-24V dc – wh 4-20mA gn Discrete gy Load 68 Laser Control 5-24V dc ye Teach (2.70" ...
Page 10
... R172 mm (6.77") ø5.0 mm (0.20") 14.0 mm (0.55") 5.0 mm 65.0 mm (0.20") (2.56") 32.0 mm 85.5 mm (1.26") (3.36") Pinout (Female View) Gray 14.2 mm Yellow (0.56") Green Brown Size Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Red or Pink Blue White Shield ...
Page 11
... X R 3.3 mm (0.13") 54.1 mm (2.13") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 LT3 Time-of-Flight Sensor – Mounting Brackets 4x R5.0 mm (0.20") 355.2° 72.0 mm (2.83") 16x R2.5 mm (0.09") 17.0 mm (0.67") 19.0 mm (0.74" ...
Page 12
... L-GAGE LT3 Time-of-Flight Sensor – P/N 68504 rev. C Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com Retro, Analog/Discrete WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period ...