SMBLXR BANNER ENGINEERING, SMBLXR Datasheet - Page 3
![Sensor Mounting Bracket](/photos/19/83/198339/4219390_sml.jpg)
SMBLXR
Manufacturer Part Number
SMBLXR
Description
Sensor Mounting Bracket
Manufacturer
BANNER ENGINEERING
Datasheet
1.LXS12.pdf
(4 pages)
Specifications of SMBLXR
Leaded Process Compatible
No
Peak Reflow Compatible (260 C)
No
For Use With
LX Series Light Curtains
Supply Voltage and Power
Supply Protection Circuitry
Sensing Range
Output Configuration
Output Rating
Output Protection Circuitry
Output Response Time
Minimum Object Detection
Size (M.O.D.S.)
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Application Notes
Certifications
Banner Engineering Corp.
www.bannerengineering.com • Tel: 763.544.3164
bn
bu
wh
bk
gy
shield*
Receiver
Select
Load
Load
Cabled Models
10 - 30V dc
Normal
5-30V dc
Reduced
0 - 2V dc
•
Minneapolis, MN U.S.A.
10 to 30V dc (10% maximum ripple) at less than 1 watt each for emitter and receiver (exclusive of load)
Protected against reverse polarity and transient voltages
Short-Range Models
Standard-Range Models
Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor
125 mA maximum each output
Off-state leakage current: less than 5 microamp
Output saturation voltage (PNP output): < 1 volt at 10 mA and < 1.5 volts at 100 mA
Output saturation voltage (NPN output): < 0.5 volts at 10 mA and < 0.6 volts at 100 mA
Protected against false pulse on power-up and continuous overload or short circuit of outputs
LX3: 0.8 ms ON-time; 6 ms OFF-time (5 ms OFF-delay)
LX6: 1.6 ms ON-time; 7 ms OFF-time (5 ms OFF-delay)
LX9: 2.4 ms ON-time; 7.5 ms OFF-time (5 ms OFF-delay)
LX12: 3.2 ms ON-time; 8.5 ms OFF-time (5 ms OFF-delay)
Smallest diameter rod that can be detected in sensing range: Short-Range: 5.6 mm (0.22")
Emitter:
Receiver:
Aluminum housing, die cast zinc with black e-coat painted endcaps, acrylic lens window
Meets IEC IP65
2 meter (6.5') 5-conductor (with drain) pvc-jacketed attached cable or 5-pin Euro-style 150 mm (6") QD pigtail,
depending on model
Temperature: -20° to +70° C (-4° to +158° F)
Max. rel. humidity: 90% at 50° C (non-condensing)
i) The best sensing resolution occurs within the center 80% of the sensing range (see Figure 1).
ii) Low-profile packages can be reliably detected.
iii) Outputs are active while the light screen is interrupted.
iv) For reliable detection, successive parts must be spaced up to the total of ON-time plus OFF-time apart.
(ie: 12 milliseconds for the LX12)
bn
bu
wh
bk
gy
shield*
Emitter
LED1 (green)
ON: Power ON, good sensor
OFF: Reduced Range
LED1 (yellow)
ON: Output conducting
OFF: Output not conducting
No Connection
No Connection
Select
10 - 30V dc
Normal
5-30V dc
Reduced
0 - 2V dc
Specifications
100 to 200 mm (4" to 8")
300 mm to 2 m (1' to 6.5')
Hookups
LX Series Part-Sensing Light Screens
Normal (see hookups)
*It is recommended that the shield wire be connected to earth ground or DC common.
bn
bu
wh
bk
gy
shield*
Select
Load
Load
Receiver
Standard-Range: 9.5 mm (0.38")
LX15: 4.0 ms ON-time; 9 ms OFF-time (5 ms OFF-delay)
LX18: 4.8 ms ON-time; 10 ms OFF-time (5 ms OFF-delay)
LX21: 5.6 ms ON-time; 11 ms OFF-time (5 ms OFF-delay)
LX24: 6.4 ms ON-time; 11.5 ms OFF-time (5 ms OFF-delay)
Quick-Disconnect Models
LED2 (red)
ON: Reduced range
OFF: Normal range
Flashing: Emitter hardware failure
LED2 (bicolor green/red)
Green: Normal range
Red: Reduced range
Flashing Red: Receiver hardware failure
10 - 30V dc
Normal
5-30V dc
Reduced
0 - 2V dc
75 to 150 mm (3" to 6")
150 mm to 600 mm (6" to 24")
Reduced
wh
bn
bu
bk
gy
shield*
Select
Emitter
P/N 108865 rev. D
No Connection
No Connection
10 - 30V dc
Reduced
0 - 2V dc
Normal
5-30V dc
3