SMB55F BANNER ENGINEERING, SMB55F Datasheet - Page 9
![Sensor Mounting Bracket](/photos/19/84/198411/4253848_sml.jpg)
SMB55F
Manufacturer Part Number
SMB55F
Description
Sensor Mounting Bracket
Manufacturer
BANNER ENGINEERING
Datasheet
1.SMB55RA.pdf
(12 pages)
Specifications of SMB55F
For Use With
R58E Series Expert Register Mark Sensors
Supply Voltage and Current
Supply Protection Circuitry
Output Configuration
Output Rating
Output Protection Circuitry
Output Response Time
Repeatability
Tri-Color LED
Sensing Image
Adjustments
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Vibration and
Mechanical Shock
Application Notes
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
10 to 30V dc (10% max. ripple);
Supply current (exclusive of load current): 7 5 mA @ 10V dc
Protected against reverse polarity and transient voltages
Outputs are bipolar: one current sourcing (PNP) and one current sinking (NPN) open-collector transistor
100 mA max. (each output)
OFF-state leakage current: NPN < 200 microamps; PNP < 10 microamps (see Application Note 1)
NPN saturation: < 1.6V @ 100 mA
PNP saturation: < 3V @ 100 mA
Protected against false pulse on power-up and continuous overload or short-circuit of outputs.
50 microseconds
15 microseconds
Rectangular: 1.2 mm x 3.8 mm (0.05" x 0.15") at 10 mm (0.39") from face of lens; image oriented either parallel or
perpendicular to sensor length, depending on model (see page 1).
Red: 636 nm
Using push buttons (“+” Dynamic and “-” Static):
Using Remote TEACH input (gray wire):
8-segment Bargraph display: Red signal strength indicator relative to taught signal level; higher segment number for
higher sensing contrast
Light Operate: Green
Dark Operate: Green
Outputs Conducting: Yellow Power/Run Mode: Green
Zinc alloy die-cast and steel housing with black painted finish and o-ring sealed lens and lens port cap.
Lens: Acrylic
Push buttons: Thermoplastic elastomer
IEC IP67; NEMA 6
PVC-jacketed 5-conductor 2 m (6.5') or 9 m (30') attached cable with internal strain relief, integral 5-pin Euro-style
QD fitting, or 150 mm (6") pigtail with 5-pin Euro-style QD fitting. Mating QD cordsets are purchased separately. See
Quick-Disconnect cordsets on page 10.
Temperature: −10° to +55° C (+14° to 131° F)
Storage Temperature: −20° to +80° C (−4° to +185° F)
Maximum Relative Humidity: 90% at 50° C (non-condensing)
All models meet IEC 68-2-6 and IEC 68-2-27 testing criteria.
1. NPN OFF-state leakage current is < 200 μA for load impedances > 3kΩ or optically isolated loads.
2. Do not mount the sensor directly perpendicular to shiny surfaces; position it at approximately a 15° angle in relation
3. Minimize web or product “flutter” whenever possible to maximize sensing reliability.
For load current of 100 mA, leakage is < 1% of load current.
to the sensing target (see page 8).
Manually adjust discrete output switchpoint using “+” or “-” buttons
Dynamic TEACH (teach on-the-fly) sensitivity adjustment
Static TEACH sensitivity adjustment
Light operate/Dark operate
OFF-delay/ON-delay
Sensing beam color enable/disable
Dynamic TEACH (teach on-the-fly) sensitivity adjustment
Static TEACH sensitivity adjustment
Light operate/Dark operate
OFF-delay/ON-delay
Sensing beam color enable/disable
Disable push buttons for security
NOTE: 1 second delay on power-up; outputs do not conduct during this time.
Green: 525 nm
R58 Expert
Specifications
Blue: 472 nm
OFF-Delay: Green
ON-Delay: Green
35 mA @ 30V dc
™
Lens port cap and lens holder: ABS
Labels: Polycarbonate
Registration Mark Sensors
P/N 122928 rev. C
9